Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-690 chassis and tuner rubber washers?
#1

Was wondering if someone could tell me the correct chassis mounting washers along with the RF subchassis mounting washers for a 38-690? I see Renovated radios list them for 690/116, but dont know if that means 37/38-690...
#2

If you meant these

http://www.renovatedradios.com/product.php?product=269

these are not for RF subchassis.


And these are specifically for 690

http://www.renovatedradios.com/product.php?product=278

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

What messed with me is they both say chassis support... so the 1st ones are what support the chassis in the cabinet, I’m assuming 4 of them, and the set of 3 are for the tuner sub-chassis that sets on the main chassis?
#4

To support the subchassis you need three - one rear and two sides.

There was also (haven't found it) a small grommet that goes in the tuning cap itself for the rotor support. But it is not for the chassis itself and you might or might not need it.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

Trivia - the 2 side supports are slightly different from the one in the back.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#6

Yes I think the back one has longer internal cylinder than the sides.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Heathkit Sweep Generator TS-4
Ron Instead of Quick reply, go to New Reply, then go to the title of the very first post, and change the title text the...morzh — 02:00 PM
6TPZ and 5TPO Radio Help
I am not a specialist in car radios. I suspect they might use vibrators to convert 12V to acceptable tube voltages, so ...morzh — 01:58 PM
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM

[-]
Who's Online
There are currently 6597 online users. [Complete List]
» 3 Member(s) | 6594 Guest(s)
AvatarAvatarAvatar

>