1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 37-650 and 70 chassis washers
Oldresistor47
Junior Member
**
Posts: 27
Threads: 4
Joined: Aug 2016
City: Pembroke Pines, FL
#1

06-25-2017, 08:48 PM
Can anyone recommend a vendor for the chassis washers of these two Philcos models, whom will not charge $4.00 a washer.
Find
morzh
Odobenus rosmarus
******
Posts: 16,230
Threads: 563
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#2

06-25-2017, 08:57 PM
Yep. Lowes or Home Depot. You could buy their grommets and trim them. If this is what you want to do.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Oldresistor47
Junior Member
**
Posts: 27
Threads: 4
Joined: Aug 2016
City: Pembroke Pines, FL
#3

08-13-2017, 05:56 PM
Trying to finish this 37-650 and after several weeks of not working on it, I am not receiving any stations lower than 710 AM. Tried to start alignment and found AC signal just above 200 volts A/C. Procedure indicates meter should be in the 30 volt range. I have the positive on the plate of one of the audio amp tubes and negative on cathode. Any suggestions as to could be the problem. I don't get ay meter swing when adjusting comparators neither. Thanks
Find
morzh
Odobenus rosmarus
******
Posts: 16,230
Threads: 563
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#4

08-13-2017, 07:02 PM
I am not sure how you could get 200V AC across the output tuve, but myself, I always clip my meter to the output xfmr secondary (or speaker's voice coil) and measure volts.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 27-84 BUZZ?Humm?
I would have to look at the schematic but it's not uncommon in 1930s AC radios to have the negative of one filter cap co...Arran — 02:46 AM
Model 27-84 BUZZ?Humm?
Hello Bruce, First all do mean a 37-84b ? Did you take any before and after pictures ? is it a buzz like when you touch...radiorich — 01:59 AM
B&K 1077B no video - problem solved
Hello Tim, Yes, I even check all of my replacement parts when I install them and I too had a capacitor go bad not long a...radiorich — 01:54 AM
B&K 1077B no video
I got back into it tonight. Problem found and resolved! Sometimes it helps to take a break and think things over. It was...TV MAN — 12:40 AM
6TPZ and 5TPO Radio Help
Thank you. I have to take a break from it for about a week. I'll have to do some thinking. I was toying with the idea ...R3Sons — 12:21 AM
Model 27-84 BUZZ?Humm?
Drowning in a overloud buzz/Humm. Have already changed filter caps,bakelite blocks( caps),out of speck resistors,checked...Bruce — 12:17 AM
Philco 630csx power cord
Hello Mike Here is the Link to the company the place is called Grand Brass lamp parts . I buy all my Lamp parts plus ...radiorich — 12:00 AM
Philco 40-120C Filament Wiring
Is the tube in your radio actually 35Z3 or 35Y4, or something else?morzh — 10:55 PM
Philco 630csx power cord
Second Rich's opinion. Run a separate antenna wire. Use a separate plug. Rich Where did you get this wire? Se...morzh — 10:51 PM
6TPZ and 5TPO Radio Help
On K2, pins 1&2 are shorted. On K4, Pins 1&3 are shorted. Others are OK. - your 0.047 caps are fried in both Th...morzh — 10:40 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios