Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 2 Vote(s) - 2.5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 40-140 Field Coil Replacement
#46

Thanks again. It's playing great, and with the price of new standard variacs down, I hardly ever plug in these oldies without one--especially the ones with transformers. I run at a constant 108 volts for safety. ciao !!!
#47

Hopefully this thread still has some life. After replacing the field coil with the resistor and installing a 4'' permanent magnet speaker, I was not happy with the cheap sound, so recently I changed to a 6'' speaker. The set picked up hum when I did that, so I had to increase the size of the second power cap from 4 uf to 16 uf before the hum left. I need to know if that is safe or not. Would the transformer get hotter? Seems to. Thanks !!!
#48

It shouldn't hurt anything to increase the value of the output filter cap. The transformer should not run hotter.

The extra hum was probably there all along since you did the conversion to a PM speaker; the 4 inch speaker, most likely, did not have the frequency response on the low end so that you heard it. The 6 incher obviously has a wider frequency response, so you started hearing the hum when you installed it. If the 16 uF output filter reduced the hum to an acceptable level, then you have done all you can.

--
Ron Ramirez
Ferdinand IN
#49

Ron, would the 16 uf cause the transformer to overheat? It does seem to be running a little warmer. I don't want to burn out a transformer for want of less hum. What happens inside the radio when you increase that capacitor? Thanks !!!
#50

As I said, the transformer should not run hotter with the larger cap. If it does, then something is either drawing more current than it should, or else the transformer was already marginal (that is, possibly damaged) from old, partially shorted electrolytics and continued operation in that condition.

--
Ron Ramirez
Ferdinand IN
#51

The transformer is not running overly hot. I think the difference is, on the last check the chassis was outside the case. This model does have a back on it, and there are a few tubes close to the transformer to increase the heat. Anyway, it's all good and I appreciate your responses.




Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 46-480 Electronic Restoration
It’s been too cold to solder in the garage the last couple of evenings, but it has allowed me more time to search for th...jrblasde — 07:23 PM
An attempt to remove the Field Coil from a G speaker
The part/tool you get from HD is inside the plastic, like in a bubble.RodB — 07:17 PM
An attempt to remove the Field Coil from a G speaker
Got it. Still did not get the "Bubble" part.morzh — 07:10 PM
An attempt to remove the Field Coil from a G speaker
No Mike. Clear plastic from the packaging of items you buy at Home Depot, the ones you can't open without a hack saw or ...RodB — 05:48 PM
Philco 89 indicator light.
Well thankfully that did not happen.Jim Dutridge — 05:21 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look! PS. Looked it up. They have kits and parts for mod...morzh — 02:45 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look!morzh — 02:39 PM
46-1201 Trip Switch Spring
I deleted the other thread, as it was duplicate and did not have the photo. Please proceed with this one.morzh — 02:37 PM
46-1201 Trip Switch Spring
Hello, first post here, bear with me. I've been electronically refurbishing a 46-1201 that I received from a relative. ...ConcernedFeller — 01:46 PM
An attempt to remove the Field Coil from a G speaker
I am late to this post, amazing amount of work for a speaker Mike. You must like the challenge. I have a speaker from an...Paul Philco322 — 01:04 PM

[-]
Who's Online
There are currently 10309 online users. [Complete List]
» 2 Member(s) | 10307 Guest(s)
AvatarAvatar

>