Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Work on the Philco 39-30 has begun
#31

I just discovered another problem this thing has. Above half volume, the sound becomes horribly scratchy and it starts popping extremely loudly, even with all the lights off. Is that capacitor related?

Slave to an RCA Victor CTC-25
#32

Probably so. As for the wiring on the power transformer remember it's not the original it's a Stancor replacement. Never seen one of those with rubber coated wire. Philco yes Stancor no.
Terry
#33

I also suspect that one of the tubes is questionable. When you phirst turn it on, it sounds phine, but as time goes on, the static starts to creep through more and more. When I phixed my Philco 42-327 back in September, the sound would come in crystal clear, but minutes later, it would completely phade out. I replaced the audio output tube, and it phixed the problem.

Slave to an RCA Victor CTC-25
#34

If you replace all the electrolytic and paper capacitors as a matter of course, any resistors that test bad, and flaking rubber wiring, you'll probably find you've fixed most or all of the problems. You'll also prevent more problems down the line, so you'll save yourself a lot of troubleshooting. You will have to do an alignment when you're finished, but you probably need to do that anyway.

Replacing the caps is a few evenings' work. You can make it quicker by cutting out the old caps and soldering the new caps to the remaining wire stub. It doesn't look original, but the bright yellow and orange modern caps don't look original anyway. Making it look original by restuffing caps is a lot more work.

Since you don't have a lot of rubber wire, you don't need to desolder the old wires and replace them. On all of the 40's sets I've done, I've ended up desoldering nearly everything, which takes a long time. On radios without rubber wire, I usually just cut the old caps out, which saves a lot of time.

You could have bad coils or other hard-to-replace or had-to-repair parts, but 90% of the restoration of a radio like that is resistors and capacitors. It doesn't sound as though you have bad coils because of the symptoms you write about.

John Honeycutt
#35

I'm done worrying about this radio for a while. I'll probably do a little more work to it this summer, but right now, I have a Philco 38-62 and a Zenith console to worry about.

Slave to an RCA Victor CTC-25




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
1 - 0v - correct 2 - 0v - correct 3 - 0v - --------------------- both 3 and 4 should be the same. Check L2 for being ope...morzh — 05:15 PM
B&K 1077B no video
I'm going to get back into it tonight. but I disconnected the 2 main resistors off this supply going to different parts ...TV MAN — 04:04 PM
6TPZ and 5TPO Radio Help
Sorry. The test points are as follows: 1 - 0v 2 - 0v 3 - 0v 4 - 12v 5 - 0v 6 - 11.9v 7 - 12v 8 - 12v 9 - 12v...R3Sons — 02:09 PM
6TPZ and 5TPO Radio Help
OK, so 18 and 19 as they should be. What is "everything else?" Try to be more specific in your descriptions:...morzh — 12:44 PM
6TPZ and 5TPO Radio Help
Yeah, I'm still on 5TPO. Sorry, my bad, points 1 and 2 should be points 18 and 19 (easy mistake  :think: )  X7 is shown ...R3Sons — 11:42 AM
Philco 40-120C Filament Wiring
Hi folks, I'm in the process of restoring a Philco 40-120C and I'm finding the wiring to be a bit puzzling. According to...bluecap — 11:28 AM
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM

[-]
Who's Online
There are currently no members online.

>