Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 1 Average
  • 1
  • 2
  • 3
  • 4
  • 5

60B Version 2 Grille Cloth
#1

Oh, no!  Not grille cloth again!  I’ve searched the forums but haven’t found a specific reference to version 2.

I finished the cabinet restoration a few days ago, but had second thoughts about the grille cloth.  When I acquired the set it had faded, worn & torn cloth which I assumed was original.  So I replaced it with closely-matching  Radio Daze GRC-03.  Since then I’ve noticed that none of the photos I’ve seen of a 60B Version 2 have this pattern--not even in a 1934 Philco ad picture.
 
[Image: https://farm5.staticflickr.com/4640/3820...b9687d.jpg]
[Image: https://farm5.staticflickr.com/4589/2505...39f6ba.jpg]

The set has had some previous work done, but it’s pretty old.  One filter cap is replaced with a cardboard electrolytic from the Illinois Condenser Co, so how old might that be?

Do I have the wrong grille cloth?  If so, is an appropriate replacement available?

Thanks from a woefully disappointed…
Henry
#2

Definitely the wrong cloth. Philco had not started using the chevron cloth yet when the 60B Version 2 was being produced.

This version of the 60 also used what is commonly known among collectors as the "70/90 cloth pattern".

An exact duplicate is no longer available, but you can get pretty close with Kenny Richmond's Whiskey Rayon, or Radio Daze's GRC02.

P.S. I hate to tell you this, but in that "after" photo, the cabinet was not toned properly.

--
Ron Ramirez
Ferdinand IN
#3

Thanks, Ron. I KNEW you would notice the tone. I couldn't tell the difference on the set before restoration--it all looked equally dark. I picked up the error after it was finished. But I had a good time doing it, anyway.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM
Var resistor id
Considering what it is in series with, I doubt there should be any power requirements. Of course, we should know wher...morzh — 03:23 PM
Var resistor id
Trim pot, about 1/2 watt part of focus divider. As stated 2k ohms. This appears to be a rusty chassis, resolder all ...Chas — 03:19 PM

[-]
Who's Online
There are currently 7553 online users. [Complete List]
» 2 Member(s) | 7551 Guest(s)
AvatarAvatar

>