Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A little advice
#1

I am considering the purchase of a philco 38-2670 tombstone and was hoping someone that is lucky enough to own one of these beauties could comment on the sound the radio produces. The person selling says it is really exceptional in volume and audio quality.
I can usually find a you tube video of any radio I’m looking at to at least get an idea but not this one.
I have not been able to even find the speaker size so it must be a fairly rare radio.
Any comments on what I should be paying would be appreciated, it is fully restored. Thanks in advance
#2

Looks like the spkr is an 8" the console uses the 10 1/2". The output stage is the super class A style (mostly found in console models) using 6F6's rather than than the older standard base 42's. It's a little different it has a phase inverter stage instead of a 42 driving the pair of 42's thru a transformer. Performance wise it should be able to blow the spkr out of the cabinet. Rf/IF wise nothing too exciting rf amp, pentagrid mixer, single IF amp, and det/avc circuit.

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

So if you were using an external source for music or news or whatever it should preform very well.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM
Var resistor id
Considering what it is in series with, I doubt there should be any power requirements. Of course, we should know wher...morzh — 03:23 PM
Var resistor id
Trim pot, about 1/2 watt part of focus divider. As stated 2k ohms. This appears to be a rusty chassis, resolder all ...Chas — 03:19 PM

[-]
Who's Online
There are currently 3852 online users. [Complete List]
» 1 Member(s) | 3851 Guest(s)
Avatar

>