1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
How to glue in new speaker cloth?
SteveG
Senior Member
****
Posts: 330
Threads: 40
Joined: May 2015
City: Sanger, CA State, Province, Country: California
#1

03-04-2016, 12:07 AM
I have two cabinets to glue new speaker cloth into now.  My Philco 39-17 and my Airline 62-123 console.   Having not done this in forever, I'd like to not make mistakes.  Is there a thread on the best way to do this yet, including which way to adhere first and stretching it tight, etc..  I have the 3M Super 77 spray glue and new cloth for each.  Any help is appreciated!  Thanks in advance!
Find
KCMike
Phorum Expert
*****
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
#2

03-04-2016, 01:53 PM
Hi Steve you might review this.
http://www.grillecloth.com/grillcloth/installation.php
Find
SteveG
Senior Member
****
Posts: 330
Threads: 40
Joined: May 2015
City: Sanger, CA State, Province, Country: California
#3

03-05-2016, 05:07 PM
Mike,
Thanks for the link.

Does anyone know the best way to tone down the newness on cloth that's going in an unrestored cabinet? There are some suggestions in that link, but I'm curious what method has worked best?

Steve
Find
klondike98
Phorum Moderator
******
Posts: 5,124
Threads: 271
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

03-05-2016, 08:00 PM
I seem to recall reading about someone spraying toning lacquer on the cloth to change its color but I can't locate it.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM

[-]
Who's Online
There are currently 11416 online users. [Complete List]
» 2 Member(s) | 11414 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration