Zenith TO Knob Bright Removal
Posts: 115
Threads: 24
Joined: Oct 2016
City: Whitehall PA
Does anybody know of a non-destructive way to remove the knob brights from Zenith TO knobs. I have a pair for an H500 that are a pretty corroded and I would like to polish them. I think polishing them would be a whole lot easier if I removed them.
My only idea, and I don't like it, is to drill a small hole through the knob from behind until I hit the bright. Then I could try pushing it off of the knob from behind.
It doesn't seem like there is any space around the edges to allow me to pry them off.
Can't think of anything witty.
Greg O.
Whitehall, PA
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Welcome to the Phorum!
I do not think those brights come off easily.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hi Greg and welcome,
Your up there by Bob, Klondike and he seems to have an affinity for Zenith sets too. I'm down by Philly. Removing the brights from the knobs w/o damage is going to be difficult at best as they are pretty thin. A better solution may be to just rip them out and replace w/a new one. Check your local hardware store for replacement knobs with brights for various things like light dimmers and such. Most likely you'll find something a bit larger remove and cut it down to size and fit.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 11-11-2016, 04:33 PM by Radioroslyn.)
Posts: 16,292
Threads: 567
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
If you are willing to risk (BTW, why?) - Try heat, see if they come off.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
(11-11-2016, 09:27 AM)morzh Wrote: If you are willing to risk (BTW, why?) - Try heat, see if they come off.
The knobs melt too easily. I am surprised by this one. Most of the brass falls off of the ones I have found and often has been lost. They may not be on there all that good - but good luck.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
(11-11-2016, 03:37 PM)Phlogiston Wrote: (11-11-2016, 09:27 AM)morzh Wrote: If you are willing to risk (BTW, why?) - Try heat, see if they come off.
The knobs melt too easily. I am surprised by this one. Most of the brass falls off of the ones I have found and often has been lost. They may not be on there all that good - but good luck.
Hi Guys
You also may find that the corrosion is bad enough that you can't make them look good anyway. If those where made now days they have some sort of gold tone plastic piece. I wonder if there is a gold tone plastic tape??
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 11-11-2016, 04:29 PM by Radioroslyn.)
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Greg, what model TO do you have? I have two knobs from an 8G005 that are not too bad and which you would be welcome to, but I think from the description you have a model with solid brights in the center of the knob.
[Image: https://dl.dropboxusercontent.com/u/5462...005_35.jpg]
Posts: 115
Threads: 24
Joined: Oct 2016
City: Whitehall PA
Now that the chassis' done I've gotten around to the cabinet.
I haven't decided how to remove the brights yet, but I did try buffing one on the knob. Do you know that if you buff it enough brass turns to silver  -- oops! They're so small, I figured they'd be solid brass.
I'll either get some plating compound and fix the originals or take the coward's way out and use the spare, bright-less knobs I have with the repro brights I got from Antique Electronic Supply a while back. They don't seem to carry them any more.
Can't think of anything witty.
Greg O.
Whitehall, PA
Posts: 4,818
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Maybe you could try the opposite of heat with the knob brights, freeze them instead and the glue might give out.
Regards
Arran
Posts: 670
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
just go over top of them,,,,,GLUE ????
Posts: 115
Threads: 24
Joined: Oct 2016
City: Whitehall PA
I thought about trying to freeze them. If it was cheaper I would buy some of the wart remover spray and freeze try freezing the brights in the hope they would shrink enough to crack the glue beneath them.
The other thing I thought of was to glue something to the tops of them and try to pull them off. However I think that could end badly. I don't know what would stick and if it did how I'd get it off...
Maybe if I wait 65 more years they'll fall off on their own.
Can't think of anything witty.
Greg O.
Whitehall, PA
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
An attempt to remove the Field Coil from a G speaker
|
| Got it. Still did not get the "Bubble" part.morzh — 07:10 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| No Mike. Clear plastic from the packaging of items you buy at Home Depot, the ones you can't open without a hack saw or ...RodB — 05:48 PM |
|
Philco 89 indicator light.
|
| Well thankfully that did not happen.Jim Dutridge — 05:21 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Paul, thanks,
Anything can help.
Gary
Thanks, lemme look!
PS. Looked it up. They have kits and parts for mod...morzh — 02:45 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Paul, thanks,
Anything can help.
Gary
Thanks, lemme look!morzh — 02:39 PM |
|
46-1201 Trip Switch Spring
|
| I deleted the other thread, as it was duplicate and did not have the photo.
Please proceed with this one.morzh — 02:37 PM |
|
46-1201 Trip Switch Spring
|
| Hello, first post here, bear with me.
I've been electronically refurbishing a 46-1201 that I received from a relative. ...ConcernedFeller — 01:46 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| I am late to this post, amazing amount of work for a speaker Mike. You must like the challenge. I have a speaker from an...Paul Philco322 — 01:04 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike, give this site a look for your spider. Can't hurt.
Take care and BE HEALTHY! -GaryGarySP — 12:41 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Rod,
Bubble packaging? The one I know (if you mean the large bubble type) is really thin. I have some at home.
Is there...morzh — 12:23 PM |
|
Who's Online
|
There are currently 10784 online users. [Complete List]
» 1 Member(s) | 10783 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
