Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith T724 Selenium rectifier
#1

I am finishing up a Zenith T724 and only need to replace the selenium rectifier.

The schematic is in Beitmens pages 182 and 183. each page is marked at the bottom.

http://www.americanradiohistory.com/Arch...n-1956.pdf

I cant see the info on the schematic but I was thinking that since there is a 22 ohm resistor between the selenium and the negative side of the ecaps that a simple diode would work?

  If I remember correctly, The anode goes to the negative side of the wires on the selenium and the diode goes to the 22 ohm resistor and on to the negative of the ecap.

Am I wrong here? Do I need a second resistor or a larger value?

Thanks for any help...

(at least it isn't a resisence line cord) Icon_lol

Icon_smile


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#2

Yes, the anode goes to the (-) side and the cathode (end with the stripe) goes to the + side. 

You will probably need to increase the size of the dropping resistor.  You can measure the B+ voltage and substitute higher values of resistance until it reads what it should (probably between 100 - 200 ohms).  To be safe I'd use a 2 - 5 watt resistor.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#3

Thank you!
Just to be clear:::
The wire connected to the Negative of the Selenium goes to the anode. Then Diode end goes to a 100 ohm or so 2 watt resistor. (Remove the 22ohm resistor and replace with the 2 watt 100 ohm?) Connect one end of the new resistor to the diode and connect the other end of the new resistor to the negative of the electrolytics?

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#4

Yes, you have it correct.  Just guessing on the wattage of the resistor....you might want to use a 5 watter to be safe if you have one.

If you need any diodes I can send a few 1N4007's in the mail tomorrow.  Good luck!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#5

All figured out...
I could not figure it out... it works when I hook up the selenium but I disconnect it and hook up the resistor and diode and it was dead... I FINALLY figured out that it was a 47K resistor at 5 watts... Not a 47 ohm 5 watt... UGH, Icon_lol

Thank you for the offer but I have many diodes.. And now I have lots of 47K 5 watt resistors... Icon_rolleyes

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
No Mike. Clear plastic from the packaging of items you buy at Home Depot, the ones you can't open without a hack saw or ...RodB — 05:48 PM
Philco 89 indicator light.
Well thankfully that did not happen.Jim Dutridge — 05:21 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look! PS. Looked it up. They have kits and parts for mod...morzh — 02:45 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look!morzh — 02:39 PM
46-1201 Trip Switch Spring
I deleted the other thread, as it was duplicate and did not have the photo. Please proceed with this one.morzh — 02:37 PM
46-1201 Trip Switch Spring
Hello, first post here, bear with me. I've been electronically refurbishing a 46-1201 that I received from a relative. ...ConcernedFeller — 01:46 PM
An attempt to remove the Field Coil from a G speaker
I am late to this post, amazing amount of work for a speaker Mike. You must like the challenge. I have a speaker from an...Paul Philco322 — 01:04 PM
An attempt to remove the Field Coil from a G speaker
Mike, give this site a look for your spider. Can't hurt. Take care and BE HEALTHY! -GaryGarySP — 12:41 PM
An attempt to remove the Field Coil from a G speaker
Rod, Bubble packaging? The one I know (if you mean the large bubble type) is really thin. I have some at home. Is there...morzh — 12:23 PM
An attempt to remove the Field Coil from a G speaker
Q8. What's the meaning of life? I have read that someone made a spider out of the clear plastic from bubble packagin...RodB — 11:07 AM

[-]
Who's Online
There are currently 4715 online users. [Complete List]
» 1 Member(s) | 4714 Guest(s)
Avatar

>