Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith T724 Selenium rectifier
#1

I am finishing up a Zenith T724 and only need to replace the selenium rectifier.

The schematic is in Beitmens pages 182 and 183. each page is marked at the bottom.

http://www.americanradiohistory.com/Arch...n-1956.pdf

I cant see the info on the schematic but I was thinking that since there is a 22 ohm resistor between the selenium and the negative side of the ecaps that a simple diode would work?

  If I remember correctly, The anode goes to the negative side of the wires on the selenium and the diode goes to the 22 ohm resistor and on to the negative of the ecap.

Am I wrong here? Do I need a second resistor or a larger value?

Thanks for any help...

(at least it isn't a resisence line cord) Icon_lol

Icon_smile


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#2

Yes, the anode goes to the (-) side and the cathode (end with the stripe) goes to the + side. 

You will probably need to increase the size of the dropping resistor.  You can measure the B+ voltage and substitute higher values of resistance until it reads what it should (probably between 100 - 200 ohms).  To be safe I'd use a 2 - 5 watt resistor.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#3

Thank you!
Just to be clear:::
The wire connected to the Negative of the Selenium goes to the anode. Then Diode end goes to a 100 ohm or so 2 watt resistor. (Remove the 22ohm resistor and replace with the 2 watt 100 ohm?) Connect one end of the new resistor to the diode and connect the other end of the new resistor to the negative of the electrolytics?

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#4

Yes, you have it correct.  Just guessing on the wattage of the resistor....you might want to use a 5 watter to be safe if you have one.

If you need any diodes I can send a few 1N4007's in the mail tomorrow.  Good luck!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#5

All figured out...
I could not figure it out... it works when I hook up the selenium but I disconnect it and hook up the resistor and diode and it was dead... I FINALLY figured out that it was a 47K resistor at 5 watts... Not a 47 ohm 5 watt... UGH, Icon_lol

Thank you for the offer but I have many diodes.. And now I have lots of 47K 5 watt resistors... Icon_rolleyes

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 60
This is my thread on 60 from 2016. I had to rewind the osc coil, and I actually counted the turns and then rewound i...morzh — 03:34 PM
Philco model 60
Yes, Mark belongs to the same Michigan Antique Radio Club that I do. I suspect that the oscillator coil is in need of a ...Radios1340 — 03:10 PM
A Marconi model 86
Yeah. I am dreading the thought of what to do with all my consoles when I will no longer be able to move them around. I...morzh — 02:51 PM
1947 Silvertone 7086 Wire Recorder/Phono/Radio on YouTube
Cool gadget, Buzz. I took me a couple of second to undestand that that oscillating thing makes the wire to spool correc...morzh — 02:50 PM
A Marconi model 86
My back hurts already, you could build a house with all the wood. PaulPaul Philco322 — 02:49 PM
1947 Silvertone 7086 Wire Recorder/Phono/Radio on YouTube
Part 4 of this series now uploaded link below to anyone interested Buzz — 02:39 PM
Philco model 60
Welcome to the Phorum, Radios1340!  The oscillator coil on the 60 is a common culprit.  I just bought a 60B (June 1934) ...GarySP — 02:33 PM
Philco model 60
Yes, standard alignment procedure. I can get the minuscule tone to vary when adjusting the trimmers. But you almost have...Radios1340 — 01:40 PM
A Marconi model 86
An imposing-looking radio, for sure.morzh — 12:43 PM
Philco model 60
Model 60 struck again :lol: Welcome to the Phorum! Above is the article on Model 60. Could be of some use. Now...morzh — 12:38 PM

[-]
Who's Online
There are currently 10709 online users. [Complete List]
» 3 Member(s) | 10706 Guest(s)
AvatarAvatarAvatar

>