Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Antenna Leads 116B
#1

There are two places for external antenna leads on my Philco 116B. It has antenna clips (ant and grd) above the chassis. It also has screws on a small panel on the vertical back of the chassis with the same abbreviations. My data sheets don't explain the difference. So, I'm turning to the Phorum brain trust. Anyone?    

http://www.nostalgiaair.org/pagesbymodel...013122.pdf
#2

Found a similar radio with the same setup. A label beneath the screws on the back said, TO GET ALL OF THE PERFORMANCE WHICH IS BUILT IN THIS PHILCO, CONNECT AERIAL TRANSMISSION LINE HERE.

I take it that a special "Aerial Transmission" antenna was available through Philco.
#3

Impedance wise it's similar to the old flat tv ant wire more commonly know as 300 ohm twin lead.
http://rsgb.org/main/files/2012/10/Dipole_fig31.jpg

The feeder is the twin lead going vertical. the horizontal portion are the elements cut to the wavelength or a fraction of the wavelength. A full length ant for the bcb is abt 300 meters (abt 900') long. This just element (horizontal portion).
In practicality 60-100 works well as high up as you can get it.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Here's the deal.

The Fahnestock clips are for a conventional longwire antenna and ground lead.

The screw terminals were intended for use with Philco's All-Wave Antenna System. Using the screw terminals eliminated the need for a balun. The impedance of the screw terminal input is as Terry said...but don't try to use an old TV antenna in place of the Philco All-Wave Antenna as it won't pick up very much signal.

--
Ron Ramirez
Ferdinand IN
#5

Two questions Ron -

Is the conventional clip hookup sufficient? And, is there information published regarding the All-Wave Antenna System?

Thanks, John
#6

Yes, the conventional clip hookup is quite sufficient.

As for the All-Wave Antenna, its 1937-38 equivalent, the High Efficiency Aerial, is mentioned on Chuck's site:
http://www.philcorepairbench.com/mystery/40-6112.htm

There was a thread here in the Phorum on this subject back in 2011:
http://www.philcoradio.com/phorum/showth...p?tid=3967

--
Ron Ramirez
Ferdinand IN
#7

I saw it sold on eBay few times.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 60
Welcome to the Phorum, Radios1340!  The oscillator coil on the 60 is a common culprit.  I just bought a 60B (June 1934) ...GarySP — 02:33 PM
Philco model 60
Yes, standard alignment procedure. I can get the minuscule tone to vary when adjusting the trimmers. But you almost have...Radios1340 — 01:40 PM
A Marconi model 86
An imposing-looking radio, for sure.morzh — 12:43 PM
Philco model 60
Model 60 struck again :lol: Welcome to the Phorum! Above is the article on Model 60. Could be of some use. Now...morzh — 12:38 PM
A Marconi model 86
Ooh, very nice!jrblasde — 12:19 PM
A Marconi model 86
I am picking up this radio today. The seller tells me it is all there and working.including the tuning eye. It has 13 tu...Dan Walker — 12:07 PM
Philco model 60
Hi guys! I’m a new member here but have been using your resources for quite some time. Hopefully I can get some help wit...Radios1340 — 11:52 AM
An attempt to remove the Field Coil from a G speaker
Milkjug plastic?morzh — 09:36 PM
An attempt to remove the Field Coil from a G speaker
Yep. 'Cause when I heard "buibble" I immediately thought of this and started wondering how this poly...morzh — 09:33 PM
An attempt to remove the Field Coil from a G speaker
Blister Pack, that's what I was trying to remember!RodB — 09:29 PM

[-]
Who's Online
There are currently 6693 online users. [Complete List]
» 1 Member(s) | 6692 Guest(s)
Avatar

>