Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Emerson 517 Moderne
#1

Well I had got 3 free radios a while back, one went to Terry, one is still in the box, this Emerson got done! The lighted dial pic is does not do justice, the cabinet came out OK, used Meguiars Wax and it came up good. I took the cabinet from a junker as the original had a big hole in top. 

It has been to the bench and it sounds quite nice, picks up my 250 Watt AM music station very well. So now I am wondering if I should give this to the guy who gave it to me, It was his Dad's.


https://www.flickr.com/photos/92577012@N...2698130911

What does ya think?

Paul

Tubetalk1
#2

Looks great!
Darn I thought you fixed the old cabinet!
Hear your going to be snow in pretty soon.
Got to get busy on that GE cabinet. I found
some small brads so I can nail the top back down.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

By the time I fixed the hole It would have cost me way more than the junk set, I needed a knob and I took the case. I still have a chassis that is not too bad though it has the small tubes instead of the Octal like the one we fixed. 

Paul

Tubetalk1
#4

Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink

I don't hold with furniture that talks.
#5

I would give it back, lots of memories of his dad. David
#6

(03-14-2018, 12:21 PM)EdHolland Wrote:  Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink



That is my Whirlpool console sounds good especially if change was left in your pocket. Icon_lol

Paul

Tubetalk1




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
New member
Hello jeff, Welcome aboard ! Sincerely Riochardradiorich — 06:53 PM
New member
Good picture, When was it taken? You don't look in it like a guy who has a teenage son :)morzh — 06:13 PM
New member
Love the pic! I'm southern IL, so wouldn't be much help and Bob Anderson is very good on those, but lives in Chicago are...TV MAN — 05:25 PM
Philco 40-120C Filament Wiring
:thumbup:klondike98 — 04:56 PM
Philco 40-120C Filament Wiring
With these values I think you are OK; the Cmax for this tube is 40uF. Your Vbb could rise a bit, but probably not too mu...morzh — 04:53 PM
Philco 40-120C Filament Wiring
BTW, someone had replaced the original 20uF/20uF filter cap with a 47uF/33uF cap. Do you think these values are safe on ...bluecap — 04:33 PM
Philco 40-120C Filament Wiring
You're correct. I was misinterpreting the key position. I now know where it is, and things are making sense. I appreciat...bluecap — 04:29 PM
Philco 40-120C Filament Wiring
I think Morzh has a good thought. Check the key position. The under chassis diagram in the Philco info shows an “H” for ...klondike98 — 04:25 PM
Philco 630csx power cord
Yes, the third wire goes to the stud on the side and is separate from the other two. I've usually used cloth covered ...Tynwald — 03:09 PM
New member
Have you tried Alabama Historical Radio Society? They possibly could recommend someone. I remember a name of Dee Hanes...morzh — 03:08 PM

[-]
Who's Online
There are currently 4811 online users. [Complete List]
» 1 Member(s) | 4810 Guest(s)
Avatar

>