1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 41-315 Code 121 Pilot Lamps?
NV3G
Member
***
Posts: 74
Threads: 42
Joined: May 2008
City: Shinnston, West Virginia State, Province, Country: USA
#1

07-04-2018, 03:05 PM
I am working on a Philco 41-315 Code 121. The pilot lamps are Push Button, Band Indicator - 34-2141, Scale Lights - 34-2064, and Cabinet - 34-2210. The bulbs are very difficult to remove. Any suggestions on how to remove the bulbs from the sockets would be greatly appreciated. Where do I find the information on the actual bulb numbers?

Thank you,
nv3g
Oscar
Find
LarryFS
Member
***
Posts: 120
Threads: 15
Joined: Aug 2017
City: Fort Worth State, Province, Country: TX
#2

07-04-2018, 04:18 PM
I had same problem on a Philco 38-3.  After reading Ron's article on rebuilding pilot lamps (see link below), I used a heat gun to soften the rubber so I could then extract the bulbs.  Can't help on the bulb numbers.

http://philcoradio.com/phorum/showthread...pilot+lamp

Larry
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#3

07-04-2018, 09:40 PM
All of your philco numbers crossover to #44 bulbs.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
NV3G
Member
***
Posts: 74
Threads: 42
Joined: May 2008
City: Shinnston, West Virginia State, Province, Country: USA
#4

07-05-2018, 08:45 AM
Thank you both for your prompt replys.

nv3g
Oscar
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
91H Code 126 Restore
Just to make it more confusing here is another model 91 schematic that doesn't show parts with dotted lines in that spot...Arran — 10:37 PM
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM
91H Code 126 Restore
When it comes to the cloth covered power cords, if they are not frayed, and are flexible, and if I can bend one without ...Arran — 06:21 PM
An attempt to remove the Field Coil from a G speaker
Could be. The central cylinder is OK, but the sides are...well. What's done is done. I wonder if some standard bobbine w...morzh — 06:02 PM
An attempt to remove the Field Coil from a G speaker
Mike; As I was saying it doesn't look like they used much of a bobbin for the field coil, not like a Magnavox one wou...Arran — 05:49 PM
Atwater-Kent 84, restoration.
This AK84 was bought, I think, last fall. For a whopping $100. It has been, according to the seller, restored. As I go ...morzh — 05:48 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration