Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Why is it always the right side?
#1

Today while checking out a Zenith Allegro stereo for someone, a very good question came to mind after the right channel basically died on me. Why is it always the right side that gives out on vintage, solid state stereos? I tinkered around with a few 70's stereos in the late 90's and this was already an issue then. Either dead or weak on one side. Now that I've been tinkering with solid state again, I've once again found they often go bad on the right channel. Why is this? I have actually seen Magnavox Astro-Sonic consoles that are either weak or dead on the right side, yet they play on for years in garages and stores on the left side. Either this is an oddity caused by how solid state electronics are set up or Ohio has an odd effect on electronics! Icon_confused

No matter where you go, there you are.
#2

That's not anything I encountered servicing.

Must be living in the Twilight Zone?  Yikes

Tom
#3

Well, the issue with the Zenith Allegro appears to be the vintage speakers we tried out on it. They might have tested good with the meter, but something went wrong and I think that is why the right channel conked out on the Zenith. Same speakers also caused my Realistic stereo to act strange and I think they have a date with the sledge hammer later on. Icon_sad

No matter where you go, there you are.
#4

I would guess that the volume/balance pots probably have a lot to do with it, unless you are speaking of playing records in which case the cartridges can and do get messed up.
Regards
Arran
#5

Yes, Deoxit on balance controls and volume and balance controls often fixes it. A leas it's the first step.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Eico 368 TV/FM Sweep Generator
Ron, for the future: In order to change the name of teh topic, 1. Go to the very first post. 2. Hit "Edit...morzh — 04:29 PM
6TPZ and 5TPO Radio Help
Transistors are easy. No converters. If you have input voltage, then just put some signal through. Or touch your fin...morzh — 04:25 PM
462ron
Hi Mike, I believe I tried different ways to change the header for my post but no luck. Anyway thanks for changing it fo...462ron — 04:02 PM
6TPZ and 5TPO Radio Help
Since these radios operated in harsh environments (temp changes and vibration) you could touch a soldering iron to all t...GarySP — 03:18 PM
6TPZ and 5TPO Radio Help
Thank you Gary. Hi Morzh. These radios are 6 transistor radios. Sadly no tubes. Thanks though.R3Sons — 02:19 PM
Heathkit Sweep Generator TS-4
Ron Instead of Quick reply, go to New Reply, then go to the title of the very first post, and change the title text the...morzh — 02:00 PM
6TPZ and 5TPO Radio Help
I am not a specialist in car radios. I suspect they might use vibrators to convert 12V to acceptable tube voltages, so ...morzh — 01:58 PM
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM

[-]
Who's Online
There are currently 10008 online users. [Complete List]
» 1 Member(s) | 10007 Guest(s)
Avatar

>