Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
I think I'm missing something here. I'm feeding a 455Hz signal in to troubleshoot. I get a good strong signal to the voulme control, and also on the top of C424 (.006mfd). But I get nothing on the top side of R419 right above it. Resistor ohms out just fine. Anyone lead me in the right direction? I hope this schematic is readable. Thanks.
[img] [Image: http://i1367.photobucket.com/albums/r796...jhkvn7.png][/img]
Posts: 16,313
Threads: 569
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
C423 shorted?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(09-03-2018, 05:07 PM)morzh Wrote: R423 shorted?
Did you mean C423?
Posts: 16,313
Threads: 569
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Yes, I did.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
No, C423 is O.K. I just checked it even though it's new.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
I'm missing something too. If you apply a rf signal to the volume control you shouldn't hear it. The rf signal must be rectified to covert it to an audio signal. If you want the use rf @ 455kc connect it to the control grid of the 7H7 (p6 I think). Make sure your mode switch is good and clean.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 09-03-2018, 08:38 PM by Radioroslyn.)
Posts: 16,313
Threads: 569
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
What I did not appreciate was it was 455kHz. C423 simply shorts it.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(09-03-2018, 08:37 PM)Radioroslyn Wrote: I'm missing something too. If you apply a rf signal to the volume control you shouldn't hear it. The rf signal must be rectified to covert it to an audio signal. If you want the use rf @ 455kc connect it to the control grid of the 7H7 (p6 I think). Make sure your mode switch is good and clean.
I'm using an Eico 324 RF generator with internal modulation AF out, not a strict RF signal. I just finished recapping the chassis and am in the process of alignment. Guess I should have explained that. Sorry. I'm working backwards from the amp section to find out why I'm not getting audio.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(09-03-2018, 08:59 PM)morzh Wrote: What I did not appreciate was it was 455kHz. C423 simply shorts it.
It's AF modulated RF. I used to use a "Mosquito" for tracing. Remember those?
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
I restored a 48-482 back in 2014. The toughest part was aligning the FM converter, but it can be done using a regular modulated sig gen if you carefully follow the instructions in the Philco service paperwork, it tells this alternate method. You may find my thread on this project of use. http://www.philcoradio.com/phorum/showth...?tid=10134
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Read through your thread. Might be some useful information there if I ever get through the BC part.
Posts: 16,313
Threads: 569
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Patrick
Where exactly is it that you feed the IF signal to?
I am still not sure.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(09-04-2018, 08:46 AM)morzh Wrote: Patrick
Where exactly is it that you feed the IF signal to?
I am still not sure.
I took a step back, and used the Philco troubleshooting guide. I have a strong IF signal at the grid of the 1st IF amp. I have only a very weak signal at the plate of the converter. That would indicate a problem at the 1st IF transformer, Z400. So it appears the problem most likely is there, and I was just going off on a tangent somewhere.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Found the problem! Z404, a choke/cap combination, was wired to the white lead on Z400 instead of the green lead. The two connection points are right next to each other. That caused a very weak signal from the plate of the converter. Connected it properly, aligned the IF, and picks up stations. I really think the stock speaker is too small for this radio.
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
Atwater-Kent 84, restoration.
|
| Hello Mike,
Wow ! far as my AK it does work and the cabinet is in nice shape so is my chassis anyway here is a photo of...radiorich — 02:59 AM |
|
Atwater-Kent 84, restoration.
|
| Nice radio, Mike! Here's hoping it was well rebuilt. Take care and BE HEALTHY! GaryGarySP — 12:12 AM |
|
Atwater-Kent 84, restoration.
|
| Rich
yes, this is the way I got it. I have just put it on the table and took it apart.
I suspect it even might work,...morzh — 11:31 PM |
|
Atwater-Kent 84, restoration.
|
| Hello mike,
What nice looking radio I have one AK in my collection it's a console I have not started restoring it yet ....radiorich — 11:21 PM |
|
91H Code 126 Restore
|
| Just to make it more confusing here is another model 91 schematic that doesn't show parts with dotted lines in that spot...Arran — 10:37 PM |
|
Atwater-Kent 84, restoration.
|
| The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct.
So the c...morzh — 09:41 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Arran
Yours probably then the H speaker, same as mine.morzh — 08:39 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM |
|
91H Code 126 Restore
|
| Thanks Arran,
I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM |
|
91H Code 126 Restore
|
| As I was studying this schematic I was wondering what does this dotted line means? I haven't traced it out yet.
An o...RealRider — 07:22 PM |
|
Who's Online
|
There are currently 4013 online users. [Complete List]
» 3 Member(s) | 4010 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
