Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith TO H500
#16

Has been some time, I went to FL and back, and after having received the alignment instrument I went back to the radio. After having aligned the IF I started aligning the BC band when my reception faded out. Came back after a few second power cycle.
First I thought it was a tube, and the tube lineup happened to be 100% identical to the Stromberg Carlson AWP-8, so I changed the tubes one by one to no result.
Then I checked B+ and found it drooping so I figured it was the selenium rectifier.

I changed it for the 1N4007 plus 47 ohm resistor, shich seems to be the recommended combination.
It works but the voltage on the output plate is about 10V higher than indicated (the resistor drops just 3V). Everything works but I will use a larger resistor, maybe 80 to 100 ohm, 10W or so.

Then finish the alignment.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#17

Mike;
  I would go with something between 47 and 80 Ohms resistance, with 80 at the high end, I'm not sure about the 1LN6 but the 1R5s are very fussy about how much voltage they receive,  sometimes they will stop oscillating if the voltage is cut down too much, especially on the filament side.
Regards
Arran
#18

47 seems too little even though it is (40-50) is the recommended range.
I doubt 100V is a problem, plus the radio will mostly be used with the battery. Plus large resistance will dissipate proportionately more power.
So maybe I will leave it at 47.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#19

Today the 82 ohm resistors arrived, put it in in series with the 1N4007 and have a 6V dropout bringing the 90V plate voltage to 95V from 101V. Good'nuff.
Gave it full alignment tonight, tomorrow will put it together and shelf it.
Buying them batteries for every radio is becoming a tad expensive.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#20

After having assembled the radio I found out the radio has some sort of anenna connection problem. The antenna is the one in the front cover.
So I had to pull the chassis out and take the top apart.

Looks like this:

   
   

The separation of the wire from the hings could be seen.
I soldered it back.

Seems to work.

Now need to buy thd battery.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
New member
Good picture, When was it taken? You don't look in it like a guy who has a teenage son :)morzh — 06:13 PM
New member
Love the pic! I'm southern IL, so wouldn't be much help and Bob Anderson is very good on those, but lives in Chicago are...TV MAN — 05:25 PM
Philco 40-120C Filament Wiring
:thumbup:klondike98 — 04:56 PM
Philco 40-120C Filament Wiring
With these values I think you are OK; the Cmax for this tube is 40uF. Your Vbb could rise a bit, but probably not too mu...morzh — 04:53 PM
Philco 40-120C Filament Wiring
BTW, someone had replaced the original 20uF/20uF filter cap with a 47uF/33uF cap. Do you think these values are safe on ...bluecap — 04:33 PM
Philco 40-120C Filament Wiring
You're correct. I was misinterpreting the key position. I now know where it is, and things are making sense. I appreciat...bluecap — 04:29 PM
Philco 40-120C Filament Wiring
I think Morzh has a good thought. Check the key position. The under chassis diagram in the Philco info shows an “H” for ...klondike98 — 04:25 PM
Philco 630csx power cord
Yes, the third wire goes to the stud on the side and is separate from the other two. I've usually used cloth covered ...Tynwald — 03:09 PM
New member
Have you tried Alabama Historical Radio Society? They possibly could recommend someone. I remember a name of Dee Hanes...morzh — 03:08 PM
Philco 46-480 Electronic Restoration
Nope, he can’t tell me the dimensions. Looks like I won’t be buying it.jrblasde — 02:38 PM

[-]
Who's Online
There are currently 4121 online users. [Complete List]
» 1 Member(s) | 4120 Guest(s)
Avatar

>