1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
RCA 811K question
murf
Senior Member
****
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
#1

03-23-2019, 08:56 PM
Hello fellas,
Have a question concerning my 811k .
Swapping transformers and seem to have lost my wire ID tags on a couple wires coming out of the transformer.
These are the 2 largest dia wires.
One goes to pin 2 on the 6J7 tube and the other goes to pin 7 on the 6J7 tube.
Any chance these wires could be swapped or are they specific to these connections?
Apparently my id tags came off as I removed the transformer from the chassis.
Any help would be much appreciated.
murf
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

03-23-2019, 09:29 PM
As long as you have abt 6vac across the two wires your good. Phase relationship doesn't matter.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
murf
Senior Member
****
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
#3

03-24-2019, 08:23 AM
Hi Terry,
Just want to make sure I solder them in right the first time.
Sounds like it can go either way.
Thanks to all,
murf
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#4

03-24-2019, 09:50 PM
All,

The Philco 39-6 posts have been split off into a thread of their own.

https://www.philcoradio.com/phorum/showt...?tid=19786
--
Ron Ramirez
Ferdinand IN
Find
Jake Blake
Banned
Posts: 816
Threads: 25
Joined: Mar 2014
City: Louisville, KY
#5

03-24-2019, 10:20 PM
I was wondering if that was gonna happen.    Sorry.   Icon_redface
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)