47-1227 - Radio will not tune in any stations.
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
I have a Philco model 47-1227. It has been completely restored. All capacitors and resistors have been replaced. The audio works. We get sound from the record player but unable to tune in any stations. Have minis 2.5 volts at osc. tube. osc. tube does not change voltage when tuning dial is changed. No am or fm. Any ideal what's wrong? HELP!!!!!!!!?!
(This post was last modified: 06-09-2019, 06:53 PM by Lucky.)
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Time to break out the signal generator and inject a modulated 455kc signal @ test point A. This is w/the set set up to receive an AM signal and see what you get from the spkr.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
Receive nothing from test point A or when connected to antenna
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Ok inject a 455kc signal @ pin 1 of the 6ba6 and see what you get from the spkr.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
We get nothing from pin 1
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
How about pin 6 on the 7R7.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
Pin 6 works with. Get loud tone
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
06-09-2019, 08:38 PM
Pin 6 works. Hey loud tone.
(This post was last modified: 06-09-2019, 08:39 PM by Lucky.)
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Ok so you have a problem around the 6BA6. Check the pin voltages according t o the service info. Also be sure the heater is lit.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 06-09-2019, 08:46 PM by Radioroslyn.)
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
pin 1. -.26 volts
pin 2. 0 volts
pin 3. 0 volts
pin 4. 0 volts
pin 5. 280 volts
pin 6. -1.14 volts
pin 7. .06 volts
Heater is lit
(This post was last modified: 06-09-2019, 09:09 PM by Lucky.)
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210
State, Province, Country: Kentucky
filament should be pin 3 & 4 and pin 6 should be 100v
(This post was last modified: 06-09-2019, 09:48 PM by jake wells.
Edit Reason: error
)
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
pin 3 grounded at center of tube
pin 4 shows 6.6 volts ac
The tube is lit and working
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210
State, Province, Country: Kentucky
pin 6 should not be reading -1.14 it should be 100V check the resistors and capacitors in that circuit.
Posts: 33
Threads: 3
Joined: May 2018
City: Middletown, PA
State, Province, Country: Pa
Will check Tomorrow night.
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210
State, Province, Country: Kentucky
Users browsing this thread: 12 Guest(s)
|
|
Recent Posts
|
|
Atwater-Kent 84, restoration.
|
| Well, powering it up would be too good to be true, and I had that feeling.
Before I did, I decided to check the coils...morzh — 06:02 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Thanks Chas,
sure will give it a look!morzh — 03:39 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike,
Lookup murrayatuptown on ARF. Seems he has a dilemma with surplus field coils. Could get lucky and have what y...Chas — 01:26 PM |
|
Atwater-Kent 84, restoration.
|
| Hello Mike,
I have not checked to see if my console has a fuse or not and far as sets go I have early 30s General Motor...radiorich — 11:25 AM |
|
Atwater-Kent 84, restoration.
|
| Ron
I forgot, but when you said "phone number", I remembered, caus I usually remember how I act when I need...morzh — 11:12 AM |
|
Atwater-Kent 84, restoration.
|
| You have an extensive collection of Philcos, Mike! I’m always excited to see each new one. Agreed on the power supply fu...jrblasde — 10:50 AM |
|
462ron
|
| Hi Mike, that 84 sure looks great. You don’t often see these antique radios with a fuse like yours has. I usually instal...462ron — 10:22 AM |
|
Atwater-Kent 84, restoration.
|
| Hello Mike,
Wow ! far as my AK it does work and the cabinet is in nice shape so is my chassis anyway here is a photo of...radiorich — 02:59 AM |
|
Atwater-Kent 84, restoration.
|
| Nice radio, Mike! Here's hoping it was well rebuilt. Take care and BE HEALTHY! GaryGarySP — 12:12 AM |
|
Atwater-Kent 84, restoration.
|
| Rich
yes, this is the way I got it. I have just put it on the table and took it apart.
I suspect it even might work,...morzh — 11:31 PM |
|
Who's Online
|
There are currently 4419 online users. [Complete List]
» 1 Member(s) | 4418 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")