Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Oscillator Coil 32-1311
#1

I was troubleshooting a 37-84 and found that the oscillator coil is open. The Philco part number is 32-1311. Here are my questions:

1. Is there any other Philco oscillator coil that would be an acceptable substitute? If so, do you have the Philco part number? (Maybe I can get lucky and find one at Play Things of the Past).

2. Is there any oscillator coil currently stocked by AES or Radio Daze that would be an acceptable? The IF is 470 kHz, not 455.

Thanks for your help!

Joe Connor
#2

I had this same problem on my 37-84. If it's the primary that's open, you're in luck.

Your best bet would be to rewind the primary yourself. It's not as difficult as you might believe. It's only a handful of turns (don't remember how many offhand), but the easiest thing you could do would be to unwind the primary and count the turns. Use some very light magnet wire to replace it and wind the new wire back on. An alternate fix would be to unwind the coil until you find the break, repair it, and wind it back on (considering the low number of turns, it might not be the best solution). When done, seal the coil back up with fingernail polish or some other similar solution.

If the secondary is open, that might be a tougher situation. For that I yield to Mr. Philco and/or Chuck, who can supply more specifics on the subject, since they're the experts. Icon_smile

IIRC, I used magnet wire I got at Radio Shack, and it worked fine. Good luck!

Bill

Sent from my Pentium II on the AT&T Dial Network




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Eico 368 TV/FM Sweep Generator
Ron, for the future: In order to change the name of teh topic, 1. Go to the very first post. 2. Hit "Edit...morzh — 04:29 PM
6TPZ and 5TPO Radio Help
Transistors are easy. No converters. If you have input voltage, then just put some signal through. Or touch your fin...morzh — 04:25 PM
462ron
Hi Mike, I believe I tried different ways to change the header for my post but no luck. Anyway thanks for changing it fo...462ron — 04:02 PM
6TPZ and 5TPO Radio Help
Since these radios operated in harsh environments (temp changes and vibration) you could touch a soldering iron to all t...GarySP — 03:18 PM
6TPZ and 5TPO Radio Help
Thank you Gary. Hi Morzh. These radios are 6 transistor radios. Sadly no tubes. Thanks though.R3Sons — 02:19 PM
Heathkit Sweep Generator TS-4
Ron Instead of Quick reply, go to New Reply, then go to the title of the very first post, and change the title text the...morzh — 02:00 PM
6TPZ and 5TPO Radio Help
I am not a specialist in car radios. I suspect they might use vibrators to convert 12V to acceptable tube voltages, so ...morzh — 01:58 PM
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM

[-]
Who's Online
There are currently 8426 online users. [Complete List]
» 1 Member(s) | 8425 Guest(s)
Avatar

>