Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Hammarlund HQ-129-X
#31

The tube is likely 6SS7, as the pin 7 is Cathode and should be Grounded, and pin 6 is empty, so probably just grounded for the heck of it. 6SG7 cannot b econnected that way.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#32

What tube are you talking about? All the electrical work is now done. V1, V3, V4, & V5 are all 6SS7. If you look st the schematic I provided you will see that the cathode of a 6SS7 is pin 5
#33

Yesterday I finally got around to painting the cabinet. I sprayed it with primer, and let it dry for about 4 hours, then sprayed it with gray. I let it dry outside until the sun began to set, then brought it inside, and set it up with an electric heater blowing into it to aid in the drying. I'd have pit it in my oven, but it is just a little too tall to fit, so I figure this is the best way. It dried pretty well by the time I went to bed and turned off the heater and checked it. It is dry to the touch, but today I am "cooking" it again just to let it harden more before I reinstall the guts.
#34

The HQ-129-X is DONE. I am listening to WSM in Nashville, to The Grand Old Opry. The set is hooked to my outdoor antenna and ground. It is the best receiver I have worked on. I now remember why I love Hammarlund general coverage receivers. It is connected to my Emerson bookshelf speaker, and sounds great. More important, the reception is everything I remember, better than any of my radios, except perhaps my Scott SLRM, but I would have to test them side by side. Just from my memory I would say they are VERY close, but would give the edge to this Hammarlund. I will make a video of it working soon. This is what it looks like working.
[Image: https://64.media.tumblr.com/75d04cbd9d77...be919a.jpg]
#35

Congrats!

I attended a national meeting at the Opryland Hotel years ago; the place was gigantic.

Got a chance to see the Opry. Got there too late, missed a lot of real Ol' Time and Bluegrass but did catch some. Then the more commercial Country acts came on. (This was about 25 years ago, so I can't remember what the acts were. Still, very nice. I could really like Tennessee!

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
"Let us begin to do good"- St. Francis

Best Regards, 

MrFixr55




Users browsing this thread:
[-]
Recent Posts
Gloritone 27 Radio
Another make I have seen from U.S Radio and Television was Apex Electric, or U.S Apex, the badge on some of those had a ...Arran — 12:56 AM
Philco 46-480 Electronic Restoration
I’ve consulted a couple of the books which I got from Jim Koehler, Elements of Radio Servicing (Marcus and Levy, 1947) a...jrblasde — 10:58 PM
Gloritone 27 Radio
Richard, Radiotrope was one of the many nameplates coming out of the Marion, Indiana U.S. Radio and Television Corp plan...Eliot Ness — 10:12 PM
[split] New member...
Oh... That link is gold man! Thank you so much. I'll see if I can get this thing fixed and will post the results on...HowardWoodard — 08:10 PM
[split] New member...
Gosh. I always re-discovered how to do it, took me 2-3 minutes every time. Now that I think of it, the c-clip is there b...morzh — 07:17 PM
38-690 Gill Cloth
Yeah, this one is not a chevron pattern. Ask Mike Katz, if he has something that is similar.morzh — 07:02 PM
38-690 Gill Cloth
Hi Folks, Is anyone currently selling a good reproduction of the 38-890 grill cloth? Thanks Stevetargeteye — 06:57 PM
[split] New member...
@morzh: As you can see from the pics I included, there is no clip where the vernier shaft comes out of the brass coarse ...HowardWoodard — 06:56 PM
[split] New member...
I think where the shaft comes out of the brass piece, there should be a clip.morzh — 06:47 PM
Philco 46-480 Electronic Restoration
Well, you're right but the AVC gets to the control grid through the IF secondary, no direct connection to the control gr...RodB — 06:36 PM

[-]
Who's Online
There are currently no members online.

>