Posts: 114
Threads: 6
Joined: Jul 2021
City: Pensacola
State, Province, Country: FL
I am trying to restore this model 80 and have removed the veneer on the dome part due to many broken and missing sections.
Now the question I have what is the best way to get the bend in the veneer to glue it to the basic structure. I was thinking of soaking it in water then clamping it until it dries.
I would appreciate some advice on this.
Thanks,
George
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hey George this might help answer some of your cabinet question... https://philcoradio.com/phorum/showthread.php?tid=22636
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 114
Threads: 6
Joined: Jul 2021
City: Pensacola
State, Province, Country: FL
Thanks Terry, good to hear from you,
I must have different veneer than Steve, who is the Master of all Masters. When I try to bend the veneer, it wants to crack that's why I thought of getting it wet. Also if I use Maple instead of Walnut veneer would it change the color of the medium brown walnut classic toner on the final coat?
George
Posts: 358
Threads: 4
Joined: Aug 2015
City: Monteith, Ontario CA
Nobody would fault you for buying a "backed" veneer (easiest and cheapest is paperbacked). It's way easier to install, doesn't suffer the same resistance to bending or tendency to crack that raw veneer does and over the arch nobody will ever know what you used.
Posts: 114
Threads: 6
Joined: Jul 2021
City: Pensacola
State, Province, Country: FL
Thanks John
I will look into that. I had a thought of using maple because the walnut was on backorder, but that will not work. I will wait for the walnut.
George
Posts: 4,801
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
The cabinet on my model 81 looks like it may have been maple or birch under the finish, it's obviously not a higher quality hardwood but looks acceptable. You could always go overboard but the models 80 and 81 were entry level sets, pretty much like a later AC/DC set but with a power transformer, so they cut corners wherever it made sense to.
Regards
Arran
Posts: 114
Threads: 6
Joined: Jul 2021
City: Pensacola
State, Province, Country: FL
Arran,
Thanks for the info. I have some maple, but it doesn't seem to have a lot of grain like walnut. I am also thinking of trying to put new veneer on the front which I have never attempted. Not sure I have the talent for that, but that's how you learn.
George
Posts: 114
Threads: 6
Joined: Jul 2021
City: Pensacola
State, Province, Country: FL
Posts: 1,128
Threads: 11
Joined: Jul 2020
City: Greenlawn
State, Province, Country: NY
Considering what the "before" must have looked like, this is turning out nice!!
"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
"Let us begin to do good"- St. Francis
Best Regards,
MrFixr55
Posts: 114
Threads: 6
Joined: Jul 2021
City: Pensacola
State, Province, Country: FL
Thanks for the comment Mr Fixr55,
Should have taken some before pics, it was pretty bad. Still would like to learn how to replace front with new veneer and do the cut outs for the speaker and controls.
Thats the way it is for now.
Posts: 1,229
Threads: 28
Joined: Jan 2014
City: Wellborn Florida
Posts: 1,701
Threads: 110
Joined: May 2008
City: Omak
State, Province, Country: WA
Hello George,
that turned out really nice !
Sincerely Richard
Posts: 114
Threads: 6
Joined: Jul 2021
City: Pensacola
State, Province, Country: FL
Davis and Richard, thanks for the kind remarks.
George
Posts: 1,701
Threads: 110
Joined: May 2008
City: Omak
State, Province, Country: WA
Hello George,
you, welcome and man I have a real basket case that also has a messed up cabinet my veener is a mess mine is a model 89 if I remember but cabinet even had wood filler where someone has tried make it better .
Sincerely Richard
Posts: 358
Threads: 4
Joined: Aug 2015
City: Monteith, Ontario CA
Nice job on the arch veneer - well done!
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Eico 368 TV/FM Sweep Generator
|
| Ron,
for the future:
In order to change the name of teh topic,
1. Go to the very first post.
2. Hit "Edit...morzh — 04:29 PM |
|
6TPZ and 5TPO Radio Help
|
| Transistors are easy.
No converters. If you have input voltage, then just put some signal through.
Or touch your fin...morzh — 04:25 PM |
|
462ron
|
| Hi Mike, I believe I tried different ways to change the header for my post but no luck. Anyway thanks for changing it fo...462ron — 04:02 PM |
|
6TPZ and 5TPO Radio Help
|
| Since these radios operated in harsh environments (temp changes and vibration) you could touch a soldering iron to all t...GarySP — 03:18 PM |
|
6TPZ and 5TPO Radio Help
|
| Thank you Gary. Hi Morzh. These radios are 6 transistor radios. Sadly no tubes. Thanks though.R3Sons — 02:19 PM |
|
Heathkit Sweep Generator TS-4
|
| Ron
Instead of Quick reply, go to New Reply, then go to the title of the very first post, and change the title text the...morzh — 02:00 PM |
|
6TPZ and 5TPO Radio Help
|
| I am not a specialist in car radios.
I suspect they might use vibrators to convert 12V to acceptable tube voltages, so ...morzh — 01:58 PM |
|
6TPZ and 5TPO Radio Help
|
| Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM |
|
462ron
|
| OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM |
|
6TPZ and 5TPO Radio Help
|
| Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio. I replaced the electrolytic capacitors in both. I have the SAMS m...R3Sons — 12:29 PM |
|
Who's Online
|
There are currently 8433 online users. [Complete List]
» 1 Member(s) | 8432 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
