Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Clear Schematic for 41-255
#16

RossH -

Were you looking at our copy of the 1941 Yearbook, or one that you found elsewhere?

Dale H. Cook, GR/HP/Tek Collector, Roanoke/Lynchburg, VA
https://plymouthcolony.net/starcity/radios/
#17

Ross, sorry, clicked on the wrong one. here's the down load for the 41-255 as an attachment.


Attached Files
.pdf Part44-Philco 1941 RMS Year Book.pdf Size: 1.35 MB  Downloads: 61
#18

What's really funny is I looked at the pages and saw 255 and it took me 30 sec of looking at the schematic trying to figure out why it wasn't matching what I had before it dawned on me - I had transposed the numbers in my head.

This is perfect. Besides starting to work on one of these I am going to recreate this schematic from scratch. I've done a few ten others but this will be my first Philco recreation. I'll post when it's completed and gone over a few times. 

Thank you very much for your time and consideration in doing this, and a big thank you to all who chimed in.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.
#19

Hello Ross,
We have all been there don't worry the guys here have you taken care of !!
Sincerely Richard
#20

Hi Ross,
I don't know if you still need a clear schematic for the 41-255 but here is one that I cleaned up. I added pin numbers on the tubes and corrected 2 part #s (#29 and 33 were reversed on the schematic). Also, voltages are in dark red, and where provided, I color-coded the wire color name.
Fran


Attached Files
.pdf Schematic-pdf.pdf Size: 1.37 MB  Downloads: 63
#21

AH Just noticed 1 error on my cleaned-up schematic...
Part # 27 - the 8uf electrolytic cap...The lead that is marked RED should read GRN (green). Old eyes are not what they used to be!
Fran
#22

Thank you, Fran. I'll add it to the mix.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Thank you Gary. Hi Morzh. These radios are 6 transistor radios. Sadly no tubes. Thanks though.R3Sons — 02:19 PM
Heathkit Sweep Generator TS-4
Ron Instead of Quick reply, go to New Reply, then go to the title of the very first post, and change the title text the...morzh — 02:00 PM
6TPZ and 5TPO Radio Help
I am not a specialist in car radios. I suspect they might use vibrators to convert 12V to acceptable tube voltages, so ...morzh — 01:58 PM
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM

[-]
Who's Online
There are currently 9053 online users. [Complete List]
» 1 Member(s) | 9052 Guest(s)
Avatar

>