Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 39-116 radio and remote
#46

Hello,
Thanks for the replies, everyone! I feel a bit foolish for not thinking about how transformers are actually constructed (probably comes from never taking one apart).  In my defense, I did say rewinding transformers was not in my wheelhouse. Icon_smile The explanations made perfect sense.  I feel better about looking for a replacement transformer, knowing I'm not limited to radios but can include TVs.  I did try to bring up the original transformer on a variac. When I got to around 20 V or so, the transformer started to hum and get warm, so I gave up. It is definitely toast (no pun intended).
Brad, I totally get finishing one project before moving on to the next!!
Thank you everyone1
Rich
#47

With regard to the 39-116, (at least the U.S versions) I believe that they used rubber/gutta percha wire for the leads, which of course can rot or break down causing shorts to ground, much like the old A.K transformers can, so if someone powers one up without inspecting or replacing these leads beforehand, transformer failure is a possibility.
As for viable replacements it may also be worth looking through the selection of power transformers intended for guitar amps, such as what AES has available. You will have to find out the specs of the transformer in the 39-116, add up all of the currents of the tube heaters, rectifier winding is separate, and the voltage and current of the H.V winding.
Regards
Arran
#48

Hi Arran,
Yep, my 39-116 has a fair bit of the rubber wiring that has deteriorated.  The worst is the wiring for the station lamps.  I was planning on replacing it all anyway. As for the transformer, it is a 32-8001.  The specs in the Philco parts catalog indicate it has a 6.4V 5A supply for the tubes and station lights, a 5V 2A supply for the 80 rectifier, and the 750VCT winding will handle 130 ma. The filament winding is running fairly close to its limit, if I remember it was around 4.2A.  The thyratron has its own 2V 2.5A transformer. I had not thought of checking guitar amp transformers.  Thanks for the suggestion.

Rich




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM
6TPZ and 5TPO Radio Help
I suspect it's been repaired before. And I suspect whoever repaired it, wanted to re-use old transistors' pin stubs in o...morzh — 09:24 PM
B&K 1077B no video
Thanks Rich! I'll take a look and see what he has. I know there's more modern equipment to be had, but this one I know a...TV MAN — 09:11 PM
B&K 1077B no video
Hello Tim, Here is a link to restoration of one on Phil's old radios site ! Sincerely Richard bk1077bradiorich — 09:01 PM
6TPZ and 5TPO Radio Help
I'm a little befuddled on this one. Should X5 and X4 be tied together like this?  It looks like someone added this at so...R3Sons — 07:33 PM

[-]
Who's Online
There are currently no members online.

>