Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Looking for verification of correct schematic.
#1

I would like to verify that my thoughts are correct regarding my Model 70 and its appropriate schematic.
My chassis info:
  SN# 870044 - no prefix
  Tubes: 24 (4), 27, 47, 80
Since I was unable to find a comprehensive serial number compendium I pieced together info from various sources. My understanding is that this is an early model and therefore the correct schematic should be the "Below B-22000" version. Is that correct?

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.
#2

Hello Ross. The Philco Radio Library located at the bottom of the page has the schematic with the tube count you have. Hope this helps. The later schematic included AVC, and also has a couple 35 tubes as well. Take care and BE HEALTHY! Gary

https://philcoradio.com/library/index.ph...ams-vol-1/

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#3

I think you have the correct take on your set. Ron's annotated early schematics that note the below B22000 serial numbers would confirm that (I believe that is what you are looking at as well). I'm betting the S/N 870044 is actually B10044 ??
https://philcoradio.com/library/index.ph...chematics/
#4

Klondike98,
Thank you. I'll double check that SN and get back to you.

GarySP,
Thank you for the schematic.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.
#5

Definitely 870044


Attached Files Image(s)
   

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Restore Code ??
No, that cannot be the 47. The 47 is a regular backelite block cap. Look at the chassis picture, it is shown there. Rig...morzh — 01:45 PM
Philco 91 Restore Code ??
I have changed the title of this thread from Philco 91 Schematic. I have gone through most of the cap replacements. I...dconant — 01:26 PM
462ron
Here is an online transistor substitution site… Ron462ron — 08:44 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
One way to repair a broken wire on a coil is to take a copper strand out of some 18 gauge electrical cord, make a &quo...captainclock1988 — 12:55 AM
B&K 1077B no video
Hello Tim, I once had a Jcpenny 13inch tv /monitor built by NEC come into my repairshop it would start acting up at tim...radiorich — 10:59 PM
Restoring Philco 96
Mike; The last time I took a potted condenser can apart, and it was maybe 1/4 the size of the one in the model 96, I ...Arran — 10:56 PM
Compatible crts
Bob Andersen — 08:58 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
One way to repair a broken wire on a coil is to take a copper strand out of some 18 gauge electrical cord, make a "...Arran — 08:41 PM
Restoring Philco 96
Have just aligned it. Surprisingly, it was not that much off at all. Barely. Aligning TRF sets is pure pleasue, as ther...morzh — 07:52 PM
6TPZ and 5TPO Radio Help
1 - 0v - correct 2 - 0v - correct 3 - 0v - --------------------- both 3 and 4 should be the same. Check L2 for being ope...morzh — 05:15 PM

[-]
Who's Online
There are currently 5422 online users. [Complete List]
» 1 Member(s) | 5421 Guest(s)
Avatar

>