1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 90 BC resistor question
37silverstreak
Senior Member
****
Posts: 299
Threads: 107
Joined: Mar 2011
City: Sheboygan Falls,Wisconsin
#1

01-07-2012, 09:04 PM
Doe's any one know off hand what the wattage rating is for the BC resistor, part #5365 on a Philco 90?
at some point in my 90's life something happened that caused the resistor and several other block caps and resistors to overheat. although the BC resistor still reads the correct resistance for all three sections, the coating over the 180 ohm section has broken off so I am guessing that I should probably go ahead and replace it. Thanks!
Kevin
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

01-07-2012, 11:14 PM
I don't know if that's necessary If the chassis is working properly the heating issue shouldn't be a problem. I had a problem with a model 20 where the heavy thread wound around the BC resistor had burned up/ flaked off. I would suspect that it is more of a protective coating so it won't be shorted out by coming in contact by other parts. You could probably rewind the thread over the resistor.
I'd say that your looking at a resistor that is 20-50wts.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Atwater-Kent 84, restoration.
Rich yes, this is the way I got it. I have just put it on the table and took it apart. I suspect it even might work,...morzh — 11:31 PM
Atwater-Kent 84, restoration.
Hello mike, What nice looking radio I have one AK in my collection it's a console I have not started restoring it yet ....radiorich — 11:21 PM
91H Code 126 Restore
Just to make it more confusing here is another model 91 schematic that doesn't show parts with dotted lines in that spot...Arran — 10:37 PM
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM
91H Code 126 Restore
When it comes to the cloth covered power cords, if they are not frayed, and are flexible, and if I can bend one without ...Arran — 06:21 PM
An attempt to remove the Field Coil from a G speaker
Could be. The central cylinder is OK, but the sides are...well. What's done is done. I wonder if some standard bobbine w...morzh — 06:02 PM

[-]
Who's Online
There are currently 2592 online users. [Complete List]
» 2 Member(s) | 2590 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration