Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-295 Developed Intermittent Crackling
#1

I electronically restored a 41-295. It has recently developed a crackling sound. It sometimes levels off when it's tuned to a station, but will excite back up when going down the dial. I have replaced almost all the caps except three mica caps, and I've replaced all the resistors. I've probed around looking for sold solder joints or anything loose, but have not found anything conclusive. Besides the crackling it's a fantastic set. Receives well and sounds wonderful. Any tips from the Philco experts out there on this cracking?
#2

(03-06-2012, 04:37 PM)Sourbone Wrote:  I electronically restored a 41-295. It has recently developed a crackling sound. It sometimes levels off when it's tuned to a station, but will excite back up when going down the dial. I have replaced almost all the caps except three mica caps, and I've replaced all the resistors. I've probed around looking for sold solder joints or anything loose, but have not found anything conclusive. Besides the crackling it's a fantastic set. Receives well and sounds wonderful. Any tips from the Philco experts out there on this cracking?

Could be a bad mica but I'd grab the tracer poke around till I found the problem.
Terry
#3

Only 3 mica caps to go? Replace 'em. But only after the gentle tapping and probing with a dry old chopstick reject from the kitchen. I assume that tube pins, sockets and switches have received their once every 50 years Deoxit shower.

Else you may be poking around until next Christmas.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
91H Code 126 Restore
Just to make it more confusing here is another model 91 schematic that doesn't show parts with dotted lines in that spot...Arran — 10:37 PM
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM
91H Code 126 Restore
When it comes to the cloth covered power cords, if they are not frayed, and are flexible, and if I can bend one without ...Arran — 06:21 PM
An attempt to remove the Field Coil from a G speaker
Could be. The central cylinder is OK, but the sides are...well. What's done is done. I wonder if some standard bobbine w...morzh — 06:02 PM
An attempt to remove the Field Coil from a G speaker
Mike; As I was saying it doesn't look like they used much of a bobbin for the field coil, not like a Magnavox one wou...Arran — 05:49 PM
Atwater-Kent 84, restoration.
This AK84 was bought, I think, last fall. For a whopping $100. It has been, according to the seller, restored. As I go ...morzh — 05:48 PM

[-]
Who's Online
There are currently no members online.

>