Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco 42-355 no reception
#1

radio had limited reception only w/external ant. Changed paper and electrolytic caps. Now only works w/pushbutton presets, no manual tuning.Then even stops getting anything w/pushbuttons after 2-3min.warmup.
#2

Sounds like it's time to clean the pb assy.
Terry
#3

Yes, cleaning the push button contacts is a great idea. However, when I got the 42-400 first running, I could only manually tune it in- no push button action. So, I played with it awhile, and found the oscillator coil had a bad (loose) wire going into the center of that coil. (The wire was frayed going over the top of that coil, and only one strand of the outside wire was making contact with the center wire). I was able to drip one small drop of solder on it and "catch" that single fine wire in the center from the lead. Can't hurt to check that coil. (Be extremely careful when checking that, though-very delicate). Also, check that all your tubes are lit- jiggle the xxl and xxfm tubes and and wait a few seconds to see if that helps. (Sometimes the contacts at the tube bases are dirty). Good luck.
#4

I cleaned the tube sockets and disassembled the push button assembly and cleaned the contacts. now the presets work but still no manual tuning.
#5

That is the way it kind of was going for me for a brief amount of time. Sometimes it would only tune in stations with the pushbuttons, next time it would only work by manually tuning it. What it boiled down to was DEFINATELY that oscillator coil (for me anyway). The stranded wires went over the top of the coil form (quite tightly) and was attached to that single hair wire in the center of the form. When I touched it with my insulated prod, it bridged the gap and functioned normally. Fixed it as stated earlier. Hopefully your fix will be as easy as mine was. Luck be with you!
#6

Checked oscillator coil tests good. when connected to an external antenna there is an area around 600 on the am dial that receives static with the volume turned all the way up.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
The part/tool you get from HD is inside the plastic, like in a bubble.RodB — 07:17 PM
An attempt to remove the Field Coil from a G speaker
Got it. Still did not get the "Bubble" part.morzh — 07:10 PM
An attempt to remove the Field Coil from a G speaker
No Mike. Clear plastic from the packaging of items you buy at Home Depot, the ones you can't open without a hack saw or ...RodB — 05:48 PM
Philco 89 indicator light.
Well thankfully that did not happen.Jim Dutridge — 05:21 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look! PS. Looked it up. They have kits and parts for mod...morzh — 02:45 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look!morzh — 02:39 PM
46-1201 Trip Switch Spring
I deleted the other thread, as it was duplicate and did not have the photo. Please proceed with this one.morzh — 02:37 PM
46-1201 Trip Switch Spring
Hello, first post here, bear with me. I've been electronically refurbishing a 46-1201 that I received from a relative. ...ConcernedFeller — 01:46 PM
An attempt to remove the Field Coil from a G speaker
I am late to this post, amazing amount of work for a speaker Mike. You must like the challenge. I have a speaker from an...Paul Philco322 — 01:04 PM
An attempt to remove the Field Coil from a G speaker
Mike, give this site a look for your spider. Can't hurt. Take care and BE HEALTHY! -GaryGarySP — 12:41 PM

[-]
Who's Online
There are currently 10889 online users. [Complete List]
» 2 Member(s) | 10887 Guest(s)
AvatarAvatar

>