1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Tube bloat in an RCA?
BrendaAnnD
Phorum Expert
*****
Posts: 1,106
Threads: 88
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#16

06-10-2013, 08:09 PM
Looking through Beitman's early Crosley sets, the ones with the most bloat and convoluted circuitry I think I've ever seen are the model 160 and 171, each with 12 tubes.
Find
Jayce
Phorum Expert
*****
Posts: 2,031
Threads: 367
Joined: Jun 2010
City: Dover, OH
#17

06-10-2013, 08:59 PM
Well, I seem to be in a major holding pattern on this radio and a few other deals, including three radios I am trying to sell. Might end up having to throw in the towel and persue other interests for a bit.
No matter where you go, there you are.
Find
Paul Philco322
Super Moderator
******
Posts: 4,406
Threads: 415
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#18

06-10-2013, 09:07 PM
I have seen several Crosleys I have thought were aesthetically pleasing to view but have not had the confidence in the innards to go for it. I have to keep looking. If the tube set up does seriously contribute to performance why bother. Like those old ads, "6 tubes provide 8 tube performance" they said that to think you were getting a hot set. On the other hand just cause a set has 10 tubes it can still be a clunker.

Paul
Tubetalk1
Website Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#19

06-12-2013, 03:40 PM
The D-22 is quite a set!

One thing I have always wondered about is why resort to a 2V tube when there were very good 6V tubes available?

Both the 6A3 and 6B4G are considered equivalent to the 2A3 in the RCA RC-17 manual.
Additionally, 6L6 tubes were available.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Restore Code ??
Or you could just square the current :lol: As for the values, they are dependent on the 1 or 2-speaker system. The...morzh — 05:46 PM
Philco 91 Restore Code ??
If you know the fc resistance you can use 120 ma nominal current through the resistor to get the voltage drop then calcu...RodB — 05:21 PM
Philco 91 Restore Code ??
Thanks Mike. I at least know why it is there if I don't fully understand it. I see where you talk about a cap and resist...dconant — 04:49 PM
Philco 91 Restore Code ??
Well, this cap you showed cannot possibly, due to the way it is constructed, be 1000pF (0.001). It can be in tens of pF....morzh — 03:13 PM
Philco 91 Restore Code ??
I have two schematics for this radio one shows the 47 block (126-226) and the other (121-221) does not. My radio does no...dconant — 02:32 PM
Philco 91 Restore Code ??
No, that cannot be the 47. The 47 is a regular backelite block cap. Look at the chassis picture, it is shown there. Rig...morzh — 01:45 PM
Philco 91 Restore Code ??
I have changed the title of this thread from Philco 91 Schematic. I have gone through most of the cap replacements. I...dconant — 01:26 PM
462ron
Here is an online transistor substitution site… Ron462ron — 08:44 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
One way to repair a broken wire on a coil is to take a copper strand out of some 18 gauge electrical cord, make a &quo...captainclock1988 — 12:55 AM
B&K 1077B no video
Hello Tim, I once had a Jcpenny 13inch tv /monitor built by NEC come into my repairshop it would start acting up at tim...radiorich — 10:59 PM

[-]
Who's Online
There are currently 2460 online users. [Complete List]
» 1 Member(s) | 2459 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)