Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grunow Teledial
#16

Actually, my friend and I spent most of yesterday evening on this unit. He was wanting a challenge and I was bored, so off we went. Speaker cone was totally separated from the frame, so he epoxied that. In spite of using shims to keep the voice coil centered, it still isn't quite perfect and him and I both saw signs the spider might have been tampered with sometime in the past. Also, had to undo a 1950's or 1960's repair as we went. He worked on the chassis while I scampered for parts and tried to make sense of the Grunow capacitor code numbers in the Riders Manuals. Actually, this set is in both volume 7 and 8 of Riders, which is good because 7 had a badly printed page. It's home and back together now, but it will still need some tweaks. One thing I forgot to do was clean the band switch. Oops! It works, but is touchy. Also, the dial kept binding against the cabinet due to some sag in the chassis board, so I'll pull that and rework again. That said, this set really pulls in the stations on AM and is decent on shortwave. Sounds pretty good as well, though that speaker still isn't 100%. It's encouraging though and I figure some more tinkering will get this set up to 100%. Icon_smile

No matter where you go, there you are.
#17

Ronin: you have a metal 6L6 and what I assume is a glass 6L6 being driven by what appear to be either 6C5s or 6J5s.

Is that what your chassis calls for?
#18

6L6's and 6C5's yes.
#19

Hmm, yet another variant? One thing I wonder is: did all the variants use the same speaker? Also, I wonder why they switched to 6L6s? Mine pushes out a heck of a lot of sound with just the 6F6 tubes, though my friend thinks they might be getting pushed pretty hard. They do warm up pretty quick! I've had some radios that barely warm the 6F6 tubes and others like this one get them pretty hot.

No matter where you go, there you are.
#20

I wonder if all versions of these had the same lousy band spread on short wave? Note how it goes from 5.5 to 18 mc on a single band, pretty much like the non Teledial Grunow that Bob Andersen has. In spite of this they used a sweep hand for logging, which seems almost like a waste of time. On my G.E M-83 they used five bands, longwave, broadcast, and three shortwave bands.
With regard to using 6F6s or 6L6 tubes as final outputs, that could be because of marketing, or simply because G.H.U managed to get a deal on 6L6 tubes in bulk. Apparently this was done with one of the brand Z models, they fitted the set with 6L6 outputs for marketing purposes, just to make it look like an audio "Hot Rod", but the 6L6s didn't do very much since the power supply didn't give them the extra B+ voltage they needed, just the usual 225-250 volts.
Regards
Arran
#21

Jayce,

I hope the measurements I provided will be of some help

YOUR WELCOME!

Gene
#22

Thanks, Gene. Actually, thought I said thanks earlier, but I forgot. Sorry..

No matter where you go, there you are.
#23

Hey I just realized, Grunow copied Philco! This radio has an inclined sound board like my 116X! Hmm...Icon_think

No matter where you go, there you are.
#24

Jayce,
I am working on a Grunow 1291 right now. I am looking for an operating manual for it so I can understand the teledial and the AFC. Were you able to find a manual for it?
Thanks,
Joe Miller




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41 280 Floor radio-new project.
Rough but restorable. The rubber wiring seems to be in OK shape; the white wires often stay pliable and do not need to ...morzh — 11:03 PM
Philco 41 280 Floor radio-new project.
Hello willits18, First of all I wanted to say welcome to our little forum. over all that set does not look in to bad o...radiorich — 10:48 PM
Philco 41 280 Floor radio-new project.
Just picked this up locally. No power cord. When I tested the tubes I think I know why. 3 bad tubes, 2 shorted, and 1 ba...willits18 — 10:08 PM
Model 41-280 5 dials
for the dial you can try Radio Daze.  willits18 — 09:58 PM
Model 41-280 5 dials
For the dial you can try Radio Daze willits18 — 09:57 PM
[split] New member...
See if this helps. This is Philco Auto Tuning service bulletin. I think this is same as yours. I used it on my 37-...morzh — 08:14 PM
[split] New member...
In my shafts (yes they are a bit differnt but the idea is the same, three balls as planetary gear and a small ball and a...morzh — 08:00 PM
42-345 Resistors
Thank you to everyone who has replied. The two mystery objects are either mini cannoli or oscillators. I'm not quite su...proftrussell — 07:57 PM
[split] New member...
Btw, the thread you provided me with the service hint & tip on refurbishing this tuning shaft was written by "...HowardWoodard — 07:55 PM
[split] New member...
Yes the three ball bearings should go in the holes. The spring with teh cap should go first, then the balls (with some l...morzh — 07:21 PM

[-]
Who's Online
There are currently no members online.

>