Output tranny specs for Philco 41-300x
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
Looking to order a new Output transformer for my Philco 41-300x, and need to know the specs.
AES does not cross reference Philco part numbers with the transformers that they sell.
Would anyone know what info I would need to order the proper transformer for my radio?
Thanks,
murf
Posts: 16,273
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
Thanks again Mike,
The thread said original P.N. was 32-7997, whereas mine is 32-7981.
Any notable difference?
Sounds like there is a bit of a modification to the wiring on the Hammond.
murf
Posts: 16,273
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
All I know the Hammond 125 is pretty universal, you have the taps almost for any input to output impedance ratio.
Posts: 49
Threads: 0
Joined: Jul 2007
City: Denver CO
Part number 32-7997 is the recommended sub for a 32-7981 per the 1953 Philco parts catalog.
Posts: 4,816
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
I think that a fairly generic push pull replacement output transformer, like AES and some others sell, should work, as long as the wattage rating is high enough. Type 42s, 6F6s, 6V6s, 6BQ5s and even 6L6s are pretty close in terms of plate load impedance, a 41, a 6K6, or 6AQ5 is not however.
Regards
Arran
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
Need your opinion on new tranny.
Radio Daze suggested that the Hammond 125d is a little light.
Suggested a 125E instead.
Opinions?
murf
Posts: 16,273
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
D is a 10 watt transformer. E is a 15 Watt one.
I think the D is just fine, but the difference being mere 3 bucks......Actually I would go by size, whichever fits better. Power is not that important in this case.
Posts: 16,273
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Murf
There is no such thing as a weak OPT.
Short of keeping it on strong magnetic field and permanently saturating the core....though myself never heard of it.
Transformers do not get weak.
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
Ok, great news.
Just thought I would ask the experts.
You have been a great help Mike.
You really know your stuff.
I'll keep poking around and see if I can find anything.
Have a great night.
Thanks, murf
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Just about any PP output transformer that was about the same size and weight and period would work just fine, lower voilume if mismatch, bu no fireworks. Use what you have or can scrounge.
Users browsing this thread: 4 Guest(s)
|
Recent Posts
|
An attempt to remove the Field Coil from a G speaker
|
Gary
I in fact did, on a 38-14, I think, where I had a speaker with the dead coil.
Well...it kinda worked. Kinda, be...morzh — 10:38 PM |
An attempt to remove the Field Coil from a G speaker
|
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM |
RCA T62 is playing.....
|
Beautiful set.morzh — 09:07 PM |
An attempt to remove the Field Coil from a G speaker
|
Well....here it is.
The green stuff. Unfortunately, probably penetrates deep.
I opened the top layer and saw that:
...morzh — 08:58 PM |
Philco 91 Restore Code ??
|
:clap: :clap: :clap: :clap:
Really nice workmanship!!! Top of the chassis looks great.
Sorry about the long winded e...MrFixr55 — 08:09 PM |
Philco 40-120C Restoration
|
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM |
RCA T62 is playing.....
|
Nice looking set great save. DavidDavid — 07:48 PM |
Philco 89 indicator light.
|
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM |
An attempt to remove the Field Coil from a G speaker
|
MrFixr
Yes, it is my plan to go with 45rpm spider if I go that far.
No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM |
Philco 40-120C Restoration
|
Change the tube. Check the tube's bias network.
Are any other tubes experience the drop or just this?`
Is resistor 23 OK...morzh — 07:09 PM |
Who's Online
|
There are currently 6897 online users. [Complete List] » 1 Member(s) | 6896 Guest(s)
|
|
|

|