Philco Flying Wedge 48-230
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
I bought this thinking about restoring it and then selling it on eBay, but now I like it too much and will likely keep it. I noticed some electrolytic caps were installed that differ from the schematic. Should I go back and replace what the schematic shows, or use similar values to the replacements?
Also wondering if I did want to sell it down the road..is it more valuable as restored and working or left in it's original condition?
Posts: 5,128
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Welcome to the Phorum!!
The exact values of the electrolytics are not critical but if I were restoring it I would use the values that were in the schematic and stuff them into the original electrolytic container if its still there. You should also change out the paper capacitors and check the resistors and replace if they have drifted more than 20% above their spec.
As to value I'll let others with more ebay seller experience comment
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
OK, good. That's pretty much what I thought as well. Thanks!
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
Well, after recapping and checking/changing resistors, tubes and wiring...no stations. A little background noise, but no static or anything. Checked tube voltages, which were a little high and low here and there. I get hum from touching center lug of volume knob. I checked the wiring on the 3 coils, and they looked OK. What else can I do? I don't have a signal generator.
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
The next thing to check would be the oscillator. Place a working radio tuned to clear spot on the dial around 1450. Now, tune the 48-230 to around 1000 and rock the dial. If your oscillator is working, you should be able to hear it in the working radio.
Steve
M R Radios C M Tubes
Posts: 16,241
Threads: 564
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Have you checked you tubes?
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
Yes, I checked the tubes, swapped tubes, measured voltage. I'm going to clean the sprockets and check that all pins are making contact next.
Steve-when you say rock the dial do you mean tune it up and down slightly?
Posts: 16,241
Threads: 564
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
I am sure there are more than three coils in there. Check them all.
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Quote:Steve-when you say rock the dial do you mean tune it up and down slightly?
Yes, Tune the 48-230 a little each direction. You should hear a change in the other radio.
Steve
M R Radios C M Tubes
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
IF in, IF out and Osc coils. 3 there and nothing else. I'll run tests when I get home today.
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
Steve-thanks for that oscillator test. It worked! I swapped the 2 IF coils from a working Philco and it still has no sound. Power section, audio, IF, Osc all work but why no stations?
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
If you have a schematic that you can post, it might help us find the problem.
Steve
M R Radios C M Tubes
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
OK, I attached a 2 sheet and then a blow up of the schematic. Thanks!
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Do you have a signal generator?
Steve
M R Radios C M Tubes
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
No signal generator. That would make it too easy, wouldn't it!
Users browsing this thread: 13 Guest(s)
|
|
Recent Posts
|
|
New member
|
| Good picture,
When was it taken? You don't look in it like a guy who has a teenage son :)morzh — 06:13 PM |
|
New member
|
| Love the pic! I'm southern IL, so wouldn't be much help and Bob Anderson is very good on those, but lives in Chicago are...TV MAN — 05:25 PM |
|
Philco 40-120C Filament Wiring
|
| :thumbup:klondike98 — 04:56 PM |
|
Philco 40-120C Filament Wiring
|
| With these values I think you are OK; the Cmax for this tube is 40uF.
Your Vbb could rise a bit, but probably not too mu...morzh — 04:53 PM |
|
Philco 40-120C Filament Wiring
|
| BTW, someone had replaced the original 20uF/20uF filter cap with a 47uF/33uF cap. Do you think these values are safe on ...bluecap — 04:33 PM |
|
Philco 40-120C Filament Wiring
|
| You're correct. I was misinterpreting the key position. I now know where it is, and things are making sense. I appreciat...bluecap — 04:29 PM |
|
Philco 40-120C Filament Wiring
|
| I think Morzh has a good thought. Check the key position. The under chassis diagram in the Philco info shows an “H” for ...klondike98 — 04:25 PM |
|
Philco 630csx power cord
|
| Yes, the third wire goes to the stud on the side and is separate from the other two.
I've usually used cloth covered ...Tynwald — 03:09 PM |
|
New member
|
| Have you tried Alabama Historical Radio Society?
They possibly could recommend someone.
I remember a name of Dee Hanes...morzh — 03:08 PM |
|
Philco 46-480 Electronic Restoration
|
| Nope, he can’t tell me the dimensions. Looks like I won’t be buying it.jrblasde — 02:38 PM |
|
Who's Online
|
There are currently 4042 online users. [Complete List]
» 1 Member(s) | 4041 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
