Philco Flying Wedge 48-230
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
I bought this thinking about restoring it and then selling it on eBay, but now I like it too much and will likely keep it. I noticed some electrolytic caps were installed that differ from the schematic. Should I go back and replace what the schematic shows, or use similar values to the replacements?
Also wondering if I did want to sell it down the road..is it more valuable as restored and working or left in it's original condition?
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Welcome to the Phorum!!
The exact values of the electrolytics are not critical but if I were restoring it I would use the values that were in the schematic and stuff them into the original electrolytic container if its still there. You should also change out the paper capacitors and check the resistors and replace if they have drifted more than 20% above their spec.
As to value I'll let others with more ebay seller experience comment
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
OK, good. That's pretty much what I thought as well. Thanks!
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
Well, after recapping and checking/changing resistors, tubes and wiring...no stations. A little background noise, but no static or anything. Checked tube voltages, which were a little high and low here and there. I get hum from touching center lug of volume knob. I checked the wiring on the 3 coils, and they looked OK. What else can I do? I don't have a signal generator.
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
The next thing to check would be the oscillator. Place a working radio tuned to clear spot on the dial around 1450. Now, tune the 48-230 to around 1000 and rock the dial. If your oscillator is working, you should be able to hear it in the working radio.
Steve
M R Radios C M Tubes
Posts: 16,273
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Have you checked you tubes?
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
Yes, I checked the tubes, swapped tubes, measured voltage. I'm going to clean the sprockets and check that all pins are making contact next.
Steve-when you say rock the dial do you mean tune it up and down slightly?
Posts: 16,273
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
I am sure there are more than three coils in there. Check them all.
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Quote:Steve-when you say rock the dial do you mean tune it up and down slightly?
Yes, Tune the 48-230 a little each direction. You should hear a change in the other radio.
Steve
M R Radios C M Tubes
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
IF in, IF out and Osc coils. 3 there and nothing else. I'll run tests when I get home today.
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
Steve-thanks for that oscillator test. It worked! I swapped the 2 IF coils from a working Philco and it still has no sound. Power section, audio, IF, Osc all work but why no stations?
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
If you have a schematic that you can post, it might help us find the problem.
Steve
M R Radios C M Tubes
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
OK, I attached a 2 sheet and then a blow up of the schematic. Thanks!
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
Do you have a signal generator?
Steve
M R Radios C M Tubes
Posts: 34
Threads: 2
Joined: Jul 2014
City: Costa Mesa CA
No signal generator. That would make it too easy, wouldn't it!
Users browsing this thread: 8 Guest(s)
|
|
Recent Posts
|
|
An attempt to remove the Field Coil from a G speaker
|
| Gary
I in fact did, on a 38-14, I think, where I had a speaker with the dead coil.
Well...it kinda worked. Kinda, be...morzh — 10:38 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM |
|
RCA T62 is playing.....
|
| Beautiful set.morzh — 09:07 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Well....here it is.
The green stuff. Unfortunately, probably penetrates deep.
I opened the top layer and saw that:
...morzh — 08:58 PM |
|
Philco 91 Restore Code ??
|
| :clap: :clap: :clap: :clap:
Really nice workmanship!!! Top of the chassis looks great.
Sorry about the long winded e...MrFixr55 — 08:09 PM |
|
Philco 40-120C Restoration
|
| Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM |
|
RCA T62 is playing.....
|
| Nice looking set great save. DavidDavid — 07:48 PM |
|
Philco 89 indicator light.
|
| Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| MrFixr
Yes, it is my plan to go with 45rpm spider if I go that far.
No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM |
|
Philco 40-120C Restoration
|
| Change the tube. Check the tube's bias network.
Are any other tubes experience the drop or just this?`
Is resistor 23 OK...morzh — 07:09 PM |
|
Who's Online
|
There are currently 6084 online users. [Complete List]
» 1 Member(s) | 6083 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
