1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
42-1003 model 121 decent schematic
mountain man
Junior Member
**
Posts: 24
Threads: 9
Joined: Feb 2013
City: Jasper Arkansas
#1

11-29-2014, 09:23 PM
Got philco 42-1003 model 121 rider schematic is  illegible as far as values for components esp on the electrolytic s, the three in a single can, I can't read tried to clean it up but the larger it gets the worse it becomes. any suggestions?[Image: http://philcoradio.com/phorum/images/smi..._crazy.gif]
Find
Warren
Senior Member
****
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
#2

11-29-2014, 09:51 PM
(11-29-2014, 09:23 PM)mountain man Wrote:  Got philco 42-1003 model 121 rider schematic is  illegible as far as values for components esp on the electrolytic s, the three in a single can, I can't read tried to clean it up but the larger it gets the worse it becomes. any suggestions?[Image: http://philcoradio.com/phorum/images/smi..._crazy.gif]

Order schematics through Chuck . http://www.philcorepairbench.com/schematics.htm
Find
sam
Phorum Expert
*****
Posts: 2,573
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#3

11-30-2014, 12:21 AM
I have to say chucks schematic`s are great
lot of info and large print  only 7.00  great deal  Icon_clap Icon_thumbup
id #60 is 10 @ 25v
id #72 is 40-40 @150v
sam
Find
mountain man
Junior Member
**
Posts: 24
Threads: 9
Joined: Feb 2013
City: Jasper Arkansas
#4

11-30-2014, 08:20 AM
(11-30-2014, 12:21 AM)mafiamen2 Wrote:  I have to say chucks schematic`s are great
lot of info and large print  only 7.00  great deal  Icon_clap Icon_thumbup
id #60 is 10 @ 25v  
id #72 is 40-40 @150v
sam

thanks for the info will contact chuck.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

[-]
Who's Online
There are currently 7142 online users. [Complete List]
» 1 Member(s) | 7141 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration