Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Thanks, Paul. Some Canadian Philcos, I think, look better than American models. And this is one of them. I can't think of any American Philco that had a decorated glass dial like the one on this set.
Well, this is the wrong section for cabinet restoration, but here is why I can't put the 51AT chassis into the cabinet yet:
[Image: http://www.philcoradio.com/images/phorum...e00012.jpg]
[Image: http://www.philcoradio.com/images/phorum...e00013.jpg]
I bought this radio a year or two ago from a Canadian eBay seller, and some of the cabinet's joints and seams came loose in shipment. This will help stabilize the cabinet.
--
Ron Ramirez
Ferdinand IN
Posts: 4,818
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
(11-29-2014, 05:36 PM)Ron Ramirez Wrote: The alignment went OK save for one band: the 9.5 to 12 mc band. The tracking is off and while I can move the 12 mc signal lower on the scale, I cannot move it any higher than 11.6 on the scale - that is where the adjustment screw tightens up completely. The other bands all turned out fine.
Ron;
It may be worth checking the molded micas associated with that band, particularly if they are in the oscillator tank circuit. Who knows, maybe one of them is slightly leaky, or increased in value and makes the oscillator run a little off?
Regards
Arran
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Good point, Arran. But I think I will wait until the next time I have to get a few parts as I do not have any 375 pF mica caps on hand. I will pick up two; my 42-730EZ does not work at all on that band. Who knows, maybe the micas will cure both sets. Having studied the schematics of both, I think it would have to be either the 375 pF mica, or the trimmer itself.
--
Ron Ramirez
Ferdinand IN
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Back together again:
[Image: http://www.philcoradio.com/images/phorum...e00014.jpg]
Among the damage this radio suffered in shipping is the crack you see in the wood above the dial. Between that and the separation of some of the seams, it is amazing to me that the dial glass survived intact.
I'm wondering what to do about the two missing pushbuttons. There are several American Philcos that have similar buttons; but they are all rounded on the end, unlike the four remaining buttons on this one which are flat on the end. I suppose I could install a set of six American Philco pushbuttons, and call that good enough.
The next photo is for Paul:
[Image: http://www.philcoradio.com/images/phorum...e00015.jpg]
Not perfectly focused, but not bad. I'll also add this photo to the Philcos all aglow gather here thread.
--
Ron Ramirez
Ferdinand IN
Posts: 1,532
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Looks great, Ron! 
Regarding the missing buttons, your idea of using 6 from an American Philco sounds good. Or maybe use two and just file / sand the ends flat. If there's enough "meat" on the end to allow you to do that. Otherwise you might be able to make two buttons out of some wood dowel rod and paint them to match the others. Yeah, not the most ideal, but I've done that on a project or two and it worked in a pinch.
Greg V.
West Bend, WI
Member WARCI.org
Posts: 118
Threads: 1
Joined: Nov 2014
City: Georgetown, IN
Posts: 4,818
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Those pushbuttons look familiar, I think that they may have used a similar style on some pieces of test equipment.
Regards
Arran
Posts: 2,080
Threads: 154
Joined: Jan 2013
City: Westland, MI
Looks great, Ron. That radio looks like it was near my neck of the woods. WJR, WWJ, and WXYZ are all Detroit stations, and CKLW and CFCO are from Windsor and Chatham-Kent, Ontario. All are within a 75 mile radius. Take care, Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Users browsing this thread: 5 Guest(s)
|
|
Recent Posts
|
|
Philco 46-480 Electronic Restoration
|
| It’s been too cold to solder in the garage the last couple of evenings, but it has allowed me more time to search for th...jrblasde — 07:23 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| The part/tool you get from HD is inside the plastic, like in a bubble.RodB — 07:17 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Got it. Still did not get the "Bubble" part.morzh — 07:10 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| No Mike. Clear plastic from the packaging of items you buy at Home Depot, the ones you can't open without a hack saw or ...RodB — 05:48 PM |
|
Philco 89 indicator light.
|
| Well thankfully that did not happen.Jim Dutridge — 05:21 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Paul, thanks,
Anything can help.
Gary
Thanks, lemme look!
PS. Looked it up. They have kits and parts for mod...morzh — 02:45 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Paul, thanks,
Anything can help.
Gary
Thanks, lemme look!morzh — 02:39 PM |
|
46-1201 Trip Switch Spring
|
| I deleted the other thread, as it was duplicate and did not have the photo.
Please proceed with this one.morzh — 02:37 PM |
|
46-1201 Trip Switch Spring
|
| Hello, first post here, bear with me.
I've been electronically refurbishing a 46-1201 that I received from a relative. ...ConcernedFeller — 01:46 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| I am late to this post, amazing amount of work for a speaker Mike. You must like the challenge. I have a speaker from an...Paul Philco322 — 01:04 PM |
|
Who's Online
|
There are currently 9112 online users. [Complete List]
» 1 Member(s) | 9111 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
