Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What knobs were used on the Philco 16B tombstone?
#1

I have a Philco 16B tombstone, now electrically restored, cabinet OK as is. It came with three small black bakelite hex shaped knobs, but with no tuning knob. I have a LARGE black hex knob I can use, which matches some pictures of the radio I have seen. BUT, clearly the tuning knobs needs to be a set screw type rather than push-on like I have, since it takes some force to "shift gears" on the 2-speed drive. There is evidence of a set screw being used on the tuning shaft.

Does anyone have a photo of the correct knobs for this radio? I have yet to find a photo online with enough detail. The small black hex knobs may not even be original.

Thanks!
Dave
#2

Hi Dave

From your description, it sounds like you have the 5-band version of the 16B tombstone. Yes, it originally used hex knobs. I've seen some with small hex knobs on the volume and tone controls and large hex knobs on the band switch and the tuning shaft. I have also seen them with three small hex knobs across the bottom (volume, band switch, tone). I have one in here now for restoration; it has three small hex knobs across the bottom.

For your tuning knob, you need a reproduction hex knob that has a set screw, not a metal insert for push-on use. Antique Electronic Supply used to sell these; I'm not sure if they still do, as they seem to be geared more toward guitar amp enthusiasts and audiophools these days.

--
Ron Ramirez
Ferdinand IN
#3

Dave,
Here's a pic of the knobs of my 4 band version of the 16 tombstone.

[Image: http://i30.photobucket.com/albums/c344/p...KNOBS1.jpg]
Hope this is some help.
Ed Martin,
Benwood, WV
#4

I do have the 5-band version of the 16B tombstone. David Frush located a large black bakelite Philco knob with a set screw. Photo attached. Looks like this is a likely candidate for an original knob, since its shape would permit pulling it out to engage the slow speed dial drive, and the outer shape would match the larger bandswitch knob below it.

Thank all of your for your help!
Dave

[Image: http://mcclellans.com/Philco16BKnob-1.jpg]
[Image: http://mcclellans.com/Philco16BKnob-2.jpg]




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM
6TPZ and 5TPO Radio Help
I suspect it's been repaired before. And I suspect whoever repaired it, wanted to re-use old transistors' pin stubs in o...morzh — 09:24 PM
B&K 1077B no video
Thanks Rich! I'll take a look and see what he has. I know there's more modern equipment to be had, but this one I know a...TV MAN — 09:11 PM
B&K 1077B no video
Hello Tim, Here is a link to restoration of one on Phil's old radios site ! Sincerely Richard bk1077bradiorich — 09:01 PM
6TPZ and 5TPO Radio Help
I'm a little befuddled on this one. Should X5 and X4 be tied together like this?  It looks like someone added this at so...R3Sons — 07:33 PM

[-]
Who's Online
There are currently no members online.

>