Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What knobs were used on the Philco 16B tombstone?
#1

I have a Philco 16B tombstone, now electrically restored, cabinet OK as is. It came with three small black bakelite hex shaped knobs, but with no tuning knob. I have a LARGE black hex knob I can use, which matches some pictures of the radio I have seen. BUT, clearly the tuning knobs needs to be a set screw type rather than push-on like I have, since it takes some force to "shift gears" on the 2-speed drive. There is evidence of a set screw being used on the tuning shaft.

Does anyone have a photo of the correct knobs for this radio? I have yet to find a photo online with enough detail. The small black hex knobs may not even be original.

Thanks!
Dave
#2

Hi Dave

From your description, it sounds like you have the 5-band version of the 16B tombstone. Yes, it originally used hex knobs. I've seen some with small hex knobs on the volume and tone controls and large hex knobs on the band switch and the tuning shaft. I have also seen them with three small hex knobs across the bottom (volume, band switch, tone). I have one in here now for restoration; it has three small hex knobs across the bottom.

For your tuning knob, you need a reproduction hex knob that has a set screw, not a metal insert for push-on use. Antique Electronic Supply used to sell these; I'm not sure if they still do, as they seem to be geared more toward guitar amp enthusiasts and audiophools these days.

--
Ron Ramirez
Ferdinand IN
#3

Dave,
Here's a pic of the knobs of my 4 band version of the 16 tombstone.

[Image: http://i30.photobucket.com/albums/c344/p...KNOBS1.jpg]
Hope this is some help.
Ed Martin,
Benwood, WV
#4

I do have the 5-band version of the 16B tombstone. David Frush located a large black bakelite Philco knob with a set screw. Photo attached. Looks like this is a likely candidate for an original knob, since its shape would permit pulling it out to engage the slow speed dial drive, and the outer shape would match the larger bandswitch knob below it.

Thank all of your for your help!
Dave

[Image: http://mcclellans.com/Philco16BKnob-1.jpg]
[Image: http://mcclellans.com/Philco16BKnob-2.jpg]




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Heathkit Sweep Generator TS-4
Ron Instead of Quick reply, go to New Reply, then go to the title of the very first post, and change the title text the...morzh — 02:00 PM
6TPZ and 5TPO Radio Help
I am not a specialist in car radios. I suspect they might use vibrators to convert 12V to acceptable tube voltages, so ...morzh — 01:58 PM
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM

[-]
Who's Online
There are currently no members online.

>