Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 95 value
#1

Picked up a Philco 95 today.
Had been in the family since new.
Cabinet in exc. condition. No Loose veneer .
Appears that it has had some areas re-finished at some time.
Guy said it worked fine.
Brought it home and hooked it up to variac, and it play beautifully. No hum or static.
Receives signals strong through the whole dial.
Looks like original rayon covered cord to boot.
Bought this to re-sell.
Do not plan on removing the chassis.
Will just clean it up and sell.
What you Philco fans price this one at?

[Image: http://i1161.photobucket.com/albums/q509...2095-1.jpg][Image: http://i1161.photobucket.com/albums/q509...2095-2.jpg][Image: http://i1161.photobucket.com/albums/q509...2095-3.jpg]
#2

$85-120 where I am.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

 Something doesn't look right about the finish on the cabinet, for one thing it looks sort of dull, and it should be gloss. For another it doesn't look like there is any toner on the solid wood parts, like the legs, the moldings, and the edges of the cabinet doors. On my model 96 lowboy it also had this fogging effect around the edges of the front panels, and the sides of the cabinet were finished with a dark walnut lacquer. I think that someone stripped your cabinet at some point and refinished it. It's unfortunate that the photo of the model 95 highboy is of such a poor example in terms of getting the shading effect, it looks dirty or like someone smeared oil stain all over it.
Regards
Arran
#4

Yeah. Here is an original finish from a CL ad. You can see, though yellowed, the trim and legs are darker.

   

Now the same radio refinished:

   

Well after looking at his again, I suppose they could have used less toner on the top. Or maybe just the top was refinished. The legs look about right. But the white wood trim to the left and right should have been toned darker on top and bottom leaving a lighter area in the center (vertically).

That is the original finish on the bird's eye front and the inside of the doors. So I matched that level of gloss in the refinish of the rest. It probably had more gloss when new.

I think I gave $90 for this one, which was probably $40 too much as it was in the CL ad.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

[-]
Who's Online
There are currently 3039 online users. [Complete List]
» 1 Member(s) | 3038 Guest(s)
Avatar

>