my 37-61 project...

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

my 37-61 project...

~~mikethedruid~~
Banned

Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN

#15

12-13-2015, 12:10 AM

I looked more closely at that tone control when I pulled it to clean it. I would swear it is something original, were it not that I have not seen that mentioned in the revisions. Do any of our Philco experts know if the factory ever used a 1 MEG pot in this position, connected so it went between where condensers 40 and 41 meet at one terminal of the switch type control, and ground, the other connection of the control ?
http://www.nostalgiaair.org/Resources/208/M0013208.htm
(the schematics for reference)
It looks like it may be a very workable circuit. I'll be interested to see. It seems to be an audio taper pot.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

my 37-61 project... - by mikethedruid - 09-26-2015, 05:12 PM

RE: my 37-61 project... - by mikethedruid - 09-30-2015, 04:29 PM

RE: my 37-61 project... - by mikethedruid - 10-02-2015, 06:44 PM

RE: my 37-61 project... - by mikethedruid - 10-05-2015, 07:40 PM

RE: my 37-61 project... - by mikethedruid - 10-17-2015, 01:03 PM

RE: my 37-61 project... - by KCMike - 10-17-2015, 01:56 PM

RE: my 37-61 project... - by mikethedruid - 10-17-2015, 02:53 PM

RE: my 37-61 project... - by mikethedruid - 11-16-2015, 08:23 PM

RE: my 37-61 project... - by mikethedruid - 11-17-2015, 12:51 AM

RE: my 37-61 project... - by klondike98 - 11-17-2015, 01:46 AM

RE: my 37-61 project... - by mikethedruid - 11-17-2015, 03:06 AM

RE: my 37-61 project... - by mikethedruid - 12-09-2015, 10:08 PM

RE: my 37-61 project... - by kiwi_steve - 12-10-2015, 01:07 AM

RE: my 37-61 project... - by mikethedruid - 12-11-2015, 09:38 AM

RE: my 37-61 project... - by mikethedruid - 12-13-2015, 12:10 AM

RE: my 37-61 project... - by mikethedruid - 12-14-2015, 08:38 PM

RE: my 37-61 project... - by mikethedruid - 12-27-2015, 08:22 PM

RE: my 37-61 project... - by mikethedruid - 12-27-2015, 11:38 PM

RE: my 37-61 project... - by mikethedruid - 12-28-2015, 01:53 AM

RE: my 37-61 project... - by klondike98 - 12-28-2015, 10:20 AM

RE: my 37-61 project... - by mikethedruid - 01-01-2016, 01:53 AM

RE: my 37-61 project... - by mikethedruid - 01-27-2016, 03:58 PM

RE: my 37-61 project... - by KCMike - 01-27-2016, 05:35 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
6TPZ and 5TPO Radio Help
1 - 0v - correct 2 - 0v - correct 3 - 0v - --------------------- both 3 and 4 should be the same. Check L2 for being ope...morzh — 05:15 PM
B&K 1077B no video
I'm going to get back into it tonight. but I disconnected the 2 main resistors off this supply going to different parts ...TV MAN — 04:04 PM
6TPZ and 5TPO Radio Help
Sorry. The test points are as follows: 1 - 0v 2 - 0v 3 - 0v 4 - 12v 5 - 0v 6 - 11.9v 7 - 12v 8 - 12v 9 - 12v...R3Sons — 02:09 PM
6TPZ and 5TPO Radio Help
OK, so 18 and 19 as they should be. What is "everything else?" Try to be more specific in your descriptions:...morzh — 12:44 PM
6TPZ and 5TPO Radio Help
Yeah, I'm still on 5TPO. Sorry, my bad, points 1 and 2 should be points 18 and 19 (easy mistake :think: ) X7 is shown ...R3Sons — 11:42 AM
Philco 40-120C Filament Wiring
Hi folks, I'm in the process of restoring a Philco 40-120C and I'm finding the wiring to be a bit puzzling. According to...bluecap — 11:28 AM
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM

Who's Online

There are currently 6356 online users. [Complete List]
» 2 Member(s) | 6354 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me