Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Bright orange screen grid
#19

kruc Wrote:Codefox, I'm keeping the same capacitance the sets were designed for, I just wondered if my 400v caps that were at their upper voltage limit. I don't have an issue with the slightly higher price of the 630volt caps, I just happened to get some 400v units at the time. I'm trying to stay away from electrolytics whenever possible when I rebuild a unit, that's why I'm using plastic caps whenever possible. FWIW, I found 600v plastic caps at AES. B+ shouldn't be an issue after replacing the filter with the same capacitance.
Music, my 20 lists a primary of 105-125volts. However at 125 the secondaries will put out a higher voltage than the tube filaments and plates were designed for. Recent threads on ARF discussed using a bucking transformer or a resistor in series with the primary. The obvious issues are finding space for a transformer or adequate area for heatsinking a wirewound resistor. I have a Japanese superhet with a 100v primary I run off a variac as I haven't gotten around to reducing the input voltage permanently.
Dave

In my experience 400 volt condensers are usually fine in most old radios, I have a number of .047 mf 400 volt ones that I have used and none have failed. The typical plate voltage in an AC set isn't any more then 275 volts running, and maybe 350 volts on start up, most circuits will not see anywhere near that. One area where I would use a 630 volt unit is a situation where if the condenser fails that the B+ would short out of find a low resistance path to ground, some tone control circuits could have this happen. Electrolytics will work fine in place of a large paper condenser, just make sure that you get one of the right voltage and observe the polarity correctly.
For the Japanese radio I would take a look at junked printers, scanners, and other assorted consumer electronics for a bucking transformer, some were 25 or more volts at a high amperage, I would then build it into a box with a standard electrical outlet with the transformer in series with one side of the line.
Best Regards
Arran


Messages In This Thread
Bright orange screen grid - by Steve Davis - 07-23-2009, 11:48 PM
Re: Bright orange screen grid - by kruc - 07-24-2009, 01:15 AM
Re: Bright orange screen grid - by Arran - 07-24-2009, 06:54 AM
Re: Bright orange screen grid - by Ron Ramirez - 07-24-2009, 09:13 AM
Re: Bright orange screen grid - by Arran - 07-24-2009, 06:46 PM
Re: Bright orange screen grid - by Ron Ramirez - 07-24-2009, 06:58 PM
Re: Bright orange screen grid - by Steve Davis - 07-24-2009, 07:47 PM
Re: Bright orange screen grid - by kruc - 07-25-2009, 05:39 AM
Re: Bright orange screen grid - by Ron Ramirez - 07-25-2009, 10:35 PM
Re: Bright orange screen grid - by kruc - 07-26-2009, 04:53 AM
Re: Bright orange screen grid - by codefox1 - 07-26-2009, 12:57 PM
Re: Bright orange screen grid - by kruc - 07-26-2009, 02:07 PM
Re: Bright orange screen grid - by Ron Ramirez - 07-27-2009, 10:01 AM
Re: Bright orange screen grid - by kruc - 07-28-2009, 03:56 AM
Re: Bright orange screen grid - by Alan Douglas - 07-28-2009, 12:32 PM
Re: Bright orange screen grid - by Arran - 07-28-2009, 06:18 PM
Re: Bright orange screen grid - by kruc - 07-29-2009, 05:57 AM
Re: Bright orange screen grid - by Arran - 07-29-2009, 08:11 PM
Re: Bright orange screen grid - by kruc - 07-30-2009, 02:29 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM
6TPZ and 5TPO Radio Help
I suspect it's been repaired before. And I suspect whoever repaired it, wanted to re-use old transistors' pin stubs in o...morzh — 09:24 PM
B&K 1077B no video
Thanks Rich! I'll take a look and see what he has. I know there's more modern equipment to be had, but this one I know a...TV MAN — 09:11 PM
B&K 1077B no video
Hello Tim, Here is a link to restoration of one on Phil's old radios site ! Sincerely Richard bk1077bradiorich — 09:01 PM
6TPZ and 5TPO Radio Help
I'm a little befuddled on this one. Should X5 and X4 be tied together like this?  It looks like someone added this at so...R3Sons — 07:33 PM

[-]
Who's Online
There are currently no members online.

>