Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

model 16 code 125
#6

Hi Greg,
It's ur other pair of eyes. #73, Capacitance isn't very critical I used 4.7mf @450v. You can mount the replacements (4) under the chassis or cut the can and install them inside. The important thing is to be sure the old ones disconnected. + goes to the terminals - to the chassis.

#90 (8mf @450v) a 10mf is fine too + goes to the 80 filament - to the power transformer HV center tap.

#91 has two caps inside an 8mf (or or 10mf @450v) + goes to the filter choke - to the tap. The 10mf (@50v or so) the + side goes to the chassis and - to the tap. It filters the negative bias voltage for the audio stages.

Don't power it up without the spkr plugged in. Monitor the HV at the 80 filament to the chassis. If the power supply is working well and have no shorts should see about 350vdc. If you are at 250v or less you've still got a problem. You may notice plates of the 80 glowing a dull red, not good indicates a short in the HV.

GL
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
model 16 code 125 - by NostalgiaRadioTime - 09-04-2016, 09:04 PM
RE: model 16 code 125 - by morzh - 09-04-2016, 10:16 PM
RE: model 16 code 125 - by Radioroslyn - 09-04-2016, 11:23 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-05-2016, 12:27 AM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-06-2016, 07:13 PM
RE: model 16 code 125 - by Radioroslyn - 09-06-2016, 09:38 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-06-2016, 10:49 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-07-2016, 09:59 PM
RE: model 16 code 125 - by Steve Davis - 09-07-2016, 11:06 PM
RE: model 16 code 125 - by Radioroslyn - 09-07-2016, 11:17 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-08-2016, 01:31 AM
RE: model 16 code 125 - by Arran - 09-08-2016, 05:05 AM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-08-2016, 11:14 PM
RE: model 16 code 125 - by Arran - 09-09-2016, 03:36 AM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-09-2016, 10:25 AM
RE: model 16 code 125 - by Arran - 09-10-2016, 11:51 PM
RE: model 16 code 125 - by Kenneth F. Besso Jr. - 09-09-2016, 05:10 PM
RE: model 16 code 125 - by Radioroslyn - 09-09-2016, 07:50 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-11-2016, 01:27 AM
RE: model 16 code 125 - by Arran - 09-13-2016, 04:08 AM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-13-2016, 10:31 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-18-2016, 03:38 PM
RE: model 16 code 125 - by Radioroslyn - 09-18-2016, 05:05 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-18-2016, 05:32 PM
RE: model 16 code 125 - by Radioroslyn - 09-18-2016, 07:42 PM
RE: model 16 code 125 - by morzh - 09-18-2016, 09:30 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-18-2016, 10:34 PM
RE: model 16 code 125 - by Ron Ramirez - 09-20-2016, 09:48 AM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-19-2016, 10:33 PM
RE: model 16 code 125 - by Radioroslyn - 09-19-2016, 11:09 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-20-2016, 07:14 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-20-2016, 10:35 PM
RE: model 16 code 125 - by Radioroslyn - 09-20-2016, 11:14 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-20-2016, 11:34 PM
RE: model 16 code 125 - by Radioroslyn - 09-21-2016, 04:59 AM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-22-2016, 10:38 PM
RE: model 16 code 125 - by Radioroslyn - 09-23-2016, 01:01 AM
RE: model 16 code 125 - by Ron Ramirez - 09-23-2016, 06:01 AM
RE: model 16 code 125 - by Steve Davis - 09-23-2016, 08:54 AM
RE: model 16 code 125 - by Kenneth F. Besso Jr. - 09-23-2016, 05:00 PM
RE: model 16 code 125 - by Radioroslyn - 09-23-2016, 05:52 PM
RE: model 16 code 125 - by Kenneth F. Besso Jr. - 09-23-2016, 08:26 PM
RE: model 16 code 125 - by Ron Ramirez - 09-24-2016, 12:36 AM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-26-2016, 06:47 PM
RE: model 16 code 125 - by NostalgiaRadioTime - 09-27-2016, 10:35 PM
RE: model 16 code 125 - by morzh - 09-28-2016, 11:30 AM



Users browsing this thread: 23 Guest(s)
[-]
Recent Posts
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM
Philco 89 indicator light.
I forgot how the pointer is formed: could you show the way it is formed and how you tried to change it?morzh — 07:01 PM
An attempt to remove the Field Coil from a G speaker
Was that pole piece left handed ? Since the metal "spider" is toast, wonder if you can either get the "4...MrFixr55 — 06:54 PM

[-]
Who's Online
There are currently 7074 online users. [Complete List]
» 3 Member(s) | 7071 Guest(s)
AvatarAvatarAvatar

>