Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 60 alignment help
#13

(11-02-2016, 04:00 PM)Solamar Wrote:  
(11-02-2016, 03:07 PM)RadioroslynJust as an aside, the cap on the 6A7 isn\t the control grid it Wrote:  http://www.r-type.org/pdfs/6a7.pdf

So is the correct procedure to connect the freq gen to pin5?

No. If you connect the sg to pin5 it will stop the oscillator from working.
Connect to the grid cap on the 6A7.
At this point you'll want to connect the sg to the grid cap on the 6A7 then adj the IF trimmers for max with the sg turned down low so you can just hear it. After you get the IF trimmers on the back lip of the chassis peaked up connect the sg to the ant post and adj trimmer5 for minimum signal.This completes the IF alignment. Glad to help out!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 60 alignment help - by Solamar - 10-28-2016, 07:18 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-28-2016, 08:34 PM
RE: Philco 60 alignment help - by Solamar - 10-31-2016, 03:55 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 04:24 PM
RE: Philco 60 alignment help - by Solamar - 10-31-2016, 04:39 PM
RE: Philco 60 alignment help - by Radioroslyn - 10-31-2016, 06:30 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 01:39 PM
RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 03:07 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 03:59 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:00 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:09 PM
RE: Philco 60 alignment help - by Radioroslyn - 11-02-2016, 04:57 PM
RE: Philco 60 alignment help - by Solamar - 11-02-2016, 04:35 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Restoring Philco 96
Have just aligned it. Surprisingly, it was not that much off at all. Barely. Aligning TRF sets is pure pleasue, as ther...morzh — 07:52 PM
6TPZ and 5TPO Radio Help
1 - 0v - correct 2 - 0v - correct 3 - 0v - --------------------- both 3 and 4 should be the same. Check L2 for being ope...morzh — 05:15 PM
B&K 1077B no video
I'm going to get back into it tonight. but I disconnected the 2 main resistors off this supply going to different parts ...TV MAN — 04:04 PM
6TPZ and 5TPO Radio Help
Sorry. The test points are as follows: 1 - 0v 2 - 0v 3 - 0v 4 - 12v 5 - 0v 6 - 11.9v 7 - 12v 8 - 12v 9 - 12v...R3Sons — 02:09 PM
6TPZ and 5TPO Radio Help
OK, so 18 and 19 as they should be. What is "everything else?" Try to be more specific in your descriptions:...morzh — 12:44 PM
6TPZ and 5TPO Radio Help
Yeah, I'm still on 5TPO. Sorry, my bad, points 1 and 2 should be points 18 and 19 (easy mistake  :think: )  X7 is shown ...R3Sons — 11:42 AM
Philco 40-120C Filament Wiring
Hi folks, I'm in the process of restoring a Philco 40-120C and I'm finding the wiring to be a bit puzzling. According to...bluecap — 11:28 AM
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM

[-]
Who's Online
There are currently 7475 online users. [Complete List]
» 3 Member(s) | 7472 Guest(s)
AvatarAvatarAvatar

>