Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Interstage transformer problems
#1

I have a model 21, which uses a model 20 chassis in it. I have a problem that is driving me nuts. I just put my third interstage transformer in this chassis. I use this radio daily and after it has been playing for several hours, withing a few weeks of replacing the interstage transformer, the volume will drop. After some time the volume comes back up to normal. This continues for several weeks until 1/2 of the secondary of the interstage transformer opens up. When I restored this chassis 1/2 of the secondary was open so I replaced it with one I had purchased from AES. This worked and the radio played for several weeks. Then the volume would suddenly drop and without doing anything, suddenly the full volume would return. What I found unusual was whenever I attempted to check the bias voltage on the grids of the 71A's, the volume would come up by itself, until the secondary would open up completely. Checking the plate voltage on the driver tube didn't affect anything. I have changed out the transformer three times as well as I finally changed the 27 driver tube and output tubes. I thought my problem was solved, but it suddenly has come back again. I know I have seen a lot of interstage transformers where the primary was open, but never the secondary side. Any ideas? Thanks guys.


Messages In This Thread
Interstage transformer problems - by Tubesforme - 11-16-2016, 08:58 PM
RE: Interstage transformer problems - by Mondial - 11-17-2016, 08:51 AM
RE: Interstage transformer problems - by morzh - 11-17-2016, 08:25 PM
RE: Interstage transformer problems - by morzh - 11-17-2016, 09:24 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Restoring Philco 96
Have just aligned it. Surprisingly, it was not that much off at all. Barely. Aligning TRF sets is pure pleasue, as ther...morzh — 07:52 PM
6TPZ and 5TPO Radio Help
1 - 0v - correct 2 - 0v - correct 3 - 0v - --------------------- both 3 and 4 should be the same. Check L2 for being ope...morzh — 05:15 PM
B&K 1077B no video
I'm going to get back into it tonight. but I disconnected the 2 main resistors off this supply going to different parts ...TV MAN — 04:04 PM
6TPZ and 5TPO Radio Help
Sorry. The test points are as follows: 1 - 0v 2 - 0v 3 - 0v 4 - 12v 5 - 0v 6 - 11.9v 7 - 12v 8 - 12v 9 - 12v...R3Sons — 02:09 PM
6TPZ and 5TPO Radio Help
OK, so 18 and 19 as they should be. What is "everything else?" Try to be more specific in your descriptions:...morzh — 12:44 PM
6TPZ and 5TPO Radio Help
Yeah, I'm still on 5TPO. Sorry, my bad, points 1 and 2 should be points 18 and 19 (easy mistake  :think: )  X7 is shown ...R3Sons — 11:42 AM
Philco 40-120C Filament Wiring
Hi folks, I'm in the process of restoring a Philco 40-120C and I'm finding the wiring to be a bit puzzling. According to...bluecap — 11:28 AM
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM

[-]
Who's Online
There are currently 7501 online users. [Complete List]
» 2 Member(s) | 7499 Guest(s)
AvatarAvatar

>