1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 16X dial cord stringing
k6ddj
Junior Member
**
Posts: 10
Threads: 2
Joined: Jan 2017
City: Hesperia, ca
#6

01-05-2017, 01:11 PM
On looking over the pictures I have just noticed that I might have a piece missing from the rear of the vernier drive.  The string has a wide gap as it goes around the vernier pulley.  If I string it exactly like the photos, the string would enter and come out of the pulley with a very small separation from top to bottom run.  I know I am not describing this very well, but it looks like I might be missing a pulley or rubber type grommet of some sort that the string goes around on the shaft of the vernier drive rear.  If this is the case I can figure something else out to take it's place.

Dean
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Model 16X dial cord stringing - by k6ddj - 01-04-2017, 10:59 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 11:29 AM
RE: Model 16X dial cord stringing - by KCMike - 01-05-2017, 12:26 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 01:01 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 01:11 PM
RE: Model 16X dial cord stringing - by KCMike - 01-05-2017, 01:18 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 01:27 PM
RE: Model 16X dial cord stringing - by klondike98 - 01-05-2017, 01:27 PM
RE: Model 16X dial cord stringing - by KCMike - 01-05-2017, 02:12 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 02:43 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 04:36 PM
RE: Model 16X dial cord stringing - by k6ddj - 01-05-2017, 05:23 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look! PS. Looked it up. They have kits and parts for mod...morzh — 02:45 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look!morzh — 02:39 PM
46-1201 Trip Switch Spring
I deleted the other thread, as it was duplicate and did not have the photo. Please proceed with this one.morzh — 02:37 PM
46-1201 Trip Switch Spring
Hello, first post here, bear with me. I've been electronically refurbishing a 46-1201 that I received from a relative. ...ConcernedFeller — 01:46 PM
An attempt to remove the Field Coil from a G speaker
I am late to this post, amazing amount of work for a speaker Mike. You must like the challenge. I have a speaker from an...Paul Philco322 — 01:04 PM
An attempt to remove the Field Coil from a G speaker
Mike, give this site a look for your spider. Can't hurt. Take care and BE HEALTHY! -GaryGarySP — 12:41 PM
An attempt to remove the Field Coil from a G speaker
Rod, Bubble packaging? The one I know (if you mean the large bubble type) is really thin. I have some at home. Is there...morzh — 12:23 PM
An attempt to remove the Field Coil from a G speaker
Q8. What's the meaning of life? I have read that someone made a spider out of the clear plastic from bubble packagin...RodB — 11:07 AM
An attempt to remove the Field Coil from a G speaker
So, Q1. Does anyone know where to get the spider. Q2. If there is no such place, what material is best? I doubt tin is...morzh — 09:43 PM
An attempt to remove the Field Coil from a G speaker
Arran The oxidation seems to go deep, a few layers. The break starts right there, but then it will occur on every la...morzh — 07:35 PM

[-]
Who's Online
There are currently 8562 online users. [Complete List]
» 1 Member(s) | 8561 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration