1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Stuffing a 70 Can
Guest
Unregistered
 
#4

12-11-2009, 11:31 AM
The link to Chuck's site is extremely helpful ; I used it for info on restuffing bakelite blocks (hint:its a lot easier to restuff block if you just remove screw and flip over without removing wires if you do not have to). I just heated with hair dryer, cut wires and pushed old tar and junk out. I did'nt have to dig it out and make mess. Anyway, my lytic cans must be a replacement, not the copper cans shown on Chucks site. The top is not removable and it says Sprague although it has the same mount nut and stud. Maybe Ron or someone can weigh in on whether or not these cans are original to early 70 model.

Thanks Bill
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Stuffing a 70 Can - by Guest - 12-10-2009, 11:12 PM
Re: Stuffing a 70 Can - by Music in a bottle - 12-11-2009, 02:48 AM
Re: Stuffing a 70 Can - by Terry Burns - 12-11-2009, 09:11 AM
Re: Stuffing a 70 Can - by Guest - 12-11-2009, 11:31 AM
Re: Stuffing a 70 Can - by Ron Ramirez - 12-11-2009, 12:47 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
New member
Love the pic! I'm southern IL, so wouldn't be much help and Bob Anderson is very good on those, but lives in Chicago are...TV MAN — 05:25 PM
Philco 40-120C Filament Wiring
:thumbup:klondike98 — 04:56 PM
Philco 40-120C Filament Wiring
With these values I think you are OK; the Cmax for this tube is 40uF. Your Vbb could rise a bit, but probably not too mu...morzh — 04:53 PM
Philco 40-120C Filament Wiring
BTW, someone had replaced the original 20uF/20uF filter cap with a 47uF/33uF cap. Do you think these values are safe on ...bluecap — 04:33 PM
Philco 40-120C Filament Wiring
You're correct. I was misinterpreting the key position. I now know where it is, and things are making sense. I appreciat...bluecap — 04:29 PM
Philco 40-120C Filament Wiring
I think Morzh has a good thought. Check the key position. The under chassis diagram in the Philco info shows an “H” for ...klondike98 — 04:25 PM
Philco 630csx power cord
Yes, the third wire goes to the stud on the side and is separate from the other two. I've usually used cloth covered ...Tynwald — 03:09 PM
New member
Have you tried Alabama Historical Radio Society? They possibly could recommend someone. I remember a name of Dee Hanes...morzh — 03:08 PM
Philco 46-480 Electronic Restoration
Nope, he can’t tell me the dimensions. Looks like I won’t be buying it.jrblasde — 02:38 PM
Philco 46-480 Electronic Restoration
Hello Joseph , It sounds like you found a good seller and yes shipping is really expensive ! Sincerely Richardradiorich — 02:16 PM

[-]
Who's Online
There are currently 3951 online users. [Complete List]
» 1 Member(s) | 3950 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration