ID on this one tuber...?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

ID on this one tuber...?

Radioroslyn
Phorum Expert

Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#4

08-16-2017, 04:30 PM

Very kwel!!! I would guess that it was a kit of some sort. It is regenerative, the knob one the left control the regeneration, center knob is the tuning and the the knob on the right adjust the filament voltage.
Not sure about the filament wiring as the pic doesn't show it well.

Attached Files Image(s)

08-16-2017, 04:29 PM

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

ID on this one tuber...? - by klondike98 - 08-15-2017, 07:30 PM

RE: ID on this one tuber...? - by WallaceRoger - 08-15-2017, 08:06 PM

RE: ID on this one tuber...? - by Paul Philco322 - 08-15-2017, 09:48 PM

RE: ID on this one tuber...? - by Radioroslyn - 08-16-2017, 04:30 PM

RE: ID on this one tuber...? - by klondike98 - 08-17-2017, 01:03 AM

RE: ID on this one tuber...? - by Radioroslyn - 08-17-2017, 11:26 AM

RE: ID on this one tuber...? - by 462ron - 08-17-2017, 04:47 PM

RE: ID on this one tuber...? - by Arran - 08-17-2017, 06:34 PM

RE: ID on this one tuber...? - by Radioroslyn - 08-17-2017, 08:00 PM

RE: ID on this one tuber...? - by WallaceRoger - 08-17-2017, 08:35 PM

RE: ID on this one tuber...? - by klondike98 - 08-18-2017, 12:13 PM

RE: ID on this one tuber...? - by palegreenthumb - 08-18-2017, 11:39 PM

RE: ID on this one tuber...? - by Electrothaumaturgist - 10-22-2017, 06:59 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

Who's Online

There are currently 7094 online users. [Complete List]
» 1 Member(s) | 7093 Guest(s)