Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 39-55 Adventure...
#2

Wow, TWO 39-55 sets? Lucky you! Icon_smile Congratulations on your acquisition.

The radio will operate without the four tubes used in the Mystery Control section of the set. However, keep in mind that you will need to replace the motor run capacitor (59), because the off-on-volume control is operated by a motor - whether you use the Mystery Control remote or not. Also replace electrolytic (66) in the stepper circuit. In fact, you should go ahead and replace all of the paper and electrolytic capacitors, including those in the Mystery Control section, as well as any off-tolerance resistors; even if you do not plan on using the Mystery Control right away. This way, you won't have to go back into the set later on.

Cap (59) is shown as a conventional electrolytic on the schematic. It isn't! It should be replaced with a non-polarized unit rated at 30 volts or better. You might find an ideal replacement, a new motor run capacitor, at a motor rewinding shop.

Two tube vendors worthy of your consideration:

http://www.findatube.com/
http://www.vacuumtubesinc.com/

Both offer used as well as new tubes, and they stand behind what they sell.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Philco 39-55 Adventure... - by hollowstate - 04-08-2010, 12:44 AM
Re: Philco 39-55 Adventure... - by Ron Ramirez - 04-09-2010, 02:51 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
New member
Hello jeff, Welcome aboard ! Sincerely Riochardradiorich — 06:53 PM
New member
Good picture, When was it taken? You don't look in it like a guy who has a teenage son :)morzh — 06:13 PM
New member
Love the pic! I'm southern IL, so wouldn't be much help and Bob Anderson is very good on those, but lives in Chicago are...TV MAN — 05:25 PM
Philco 40-120C Filament Wiring
:thumbup:klondike98 — 04:56 PM
Philco 40-120C Filament Wiring
With these values I think you are OK; the Cmax for this tube is 40uF. Your Vbb could rise a bit, but probably not too mu...morzh — 04:53 PM
Philco 40-120C Filament Wiring
BTW, someone had replaced the original 20uF/20uF filter cap with a 47uF/33uF cap. Do you think these values are safe on ...bluecap — 04:33 PM
Philco 40-120C Filament Wiring
You're correct. I was misinterpreting the key position. I now know where it is, and things are making sense. I appreciat...bluecap — 04:29 PM
Philco 40-120C Filament Wiring
I think Morzh has a good thought. Check the key position. The under chassis diagram in the Philco info shows an “H” for ...klondike98 — 04:25 PM
Philco 630csx power cord
Yes, the third wire goes to the stud on the side and is separate from the other two. I've usually used cloth covered ...Tynwald — 03:09 PM
New member
Have you tried Alabama Historical Radio Society? They possibly could recommend someone. I remember a name of Dee Hanes...morzh — 03:08 PM

[-]
Who's Online
There are currently 4801 online users. [Complete List]
» 1 Member(s) | 4800 Guest(s)
Avatar

>