Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-180 Voltage High
#17

After testing the radio on clean city power I can report the inverter power I was previously using was my final problem after recapping. The radio sounds great now with good reception. Now I will put my newly acquired signal generator to use and get a better under standing of how it works while checking the alignment. The only other question I would throw out is if there is any way to eliminate the interference from the inverter and the CFL lighting. Some sites recommend twisting wires and adding ferrite filters. Except for the solar panels you wouldn'd know this house was any different than a city house with all normal 120VAC code wiring off of a distribution panel. I wonder if this a problem for the new homes with grid-tie inverter systems.


Messages In This Thread
40-180 Voltage High - by Bruce C - 03-29-2010, 05:20 PM
Re: 40-180 Voltage High - by DeckApe - 03-30-2010, 09:36 AM
Re: 40-180 Voltage High - by Bruce C - 03-30-2010, 10:48 AM
Re: 40-180 Voltage High - by rghines1 - 03-30-2010, 05:48 PM
Re: 40-180 Voltage High - by Bruce C - 03-30-2010, 07:18 PM
Re: 40-180 Voltage High - by rghines1 - 03-31-2010, 04:58 PM
Re: 40-180 Voltage High - by Bruce C - 03-31-2010, 10:32 PM
Re: 40-180 Voltage High - by Bruce C - 04-04-2010, 07:16 PM
Re: 40-180 Voltage High - by rghines1 - 04-05-2010, 08:47 AM
Re: 40-180 Voltage High - by Bruce C - 04-05-2010, 07:34 PM
Re: 40-180 Voltage High - by exray - 04-05-2010, 10:40 PM
Re: 40-180 Voltage High - by Raleigh - 04-05-2010, 10:59 PM
Re: 40-180 Voltage High - by exray - 04-05-2010, 11:26 PM
Re: 40-180 Voltage High - by codefox1 - 04-06-2010, 02:12 PM
Re: 40-180 Voltage High - by Bruce C - 04-06-2010, 05:08 PM
Re: 40-180 Voltage High - by Bruce C - 04-20-2010, 05:47 PM
Re: 40-180 Voltage High - by Bruce C - 04-26-2010, 05:36 PM
Re: 40-180 Voltage High - by Ron Ramirez - 04-26-2010, 05:51 PM
Re: 40-180 Voltage High - by denver - 04-26-2010, 07:28 PM
Re: 40-180 Voltage High - by Bruce C - 04-30-2010, 01:35 PM
Re: 40-180 Voltage High - by exray - 05-01-2010, 02:36 AM
Re: 40-180 Voltage High - by Bruce C - 05-07-2010, 11:03 AM
Re: 40-180 Voltage High - by codefox1 - 05-08-2010, 10:45 AM
Re: 40-180 Voltage High - by Raleigh - 05-12-2010, 02:09 PM
Re: 40-180 Voltage High - by Bruce C - 05-12-2010, 08:06 PM
Re: 40-180 Voltage High - by Bruce C - 05-12-2010, 08:06 PM
Re: 40-180 Voltage High - by Bruce C - 05-12-2010, 08:06 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

[-]
Who's Online
There are currently no members online.

>