Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 86 Curiosity
#6

Thanks guys.

@Ron - I will definitely try out the 2M value once things are running otherwise.

@Mike - Ah right! I found it: http://philcoradio.com/phorum/showthread.php?tid=17679
I should've looked earlier.

Here's where I'm at so far:

BC Resistor

The 160 ohm and 1K sections of the BC resistor were open. I created a new BC resistor out of 25W resistors. I was lucky in that the three resistors *just barely* fit.

4K resistor w/ tap: 2240 ohm + 1540 ohm sections
160 ohm Philco part
1K resistor

[Image: https://farm2.staticflickr.com/1732/2899...0b81_c.jpg]

I brought it up on the variac and it actually received quite a bit at ~80VAC.

I was fortunate that the RF coils all tested good.

Recap

I replaced the big filter can caps. Boy that was a pain to get out. The tar had previously partially melted - making it stick really well to the sides of the can.
I relied on the trick described elsewhere on the Phorum of driving a screw into the tar block (to pull on) and then heating the sides of the can with a heat gun until I could get the block out.
I also used a small thin pry bar I have to separate it from the edge of the can. It took a little of everything but eventually it came free.

[Image: https://farm2.staticflickr.com/1758/4196...0754_c.jpg]

I also replaced the 0.1uF caps inside the 100 ohm wirewound resistor tubes. Kept the original resistance wire around the tube.

Interstage Transformer

The secondary of part #26 was 1/2 open. I believe that someone long ago someone worked around that problem with this?

[Image: https://farm2.staticflickr.com/1748/4196...f890_c.jpg]

The transformer with the open winding is in the top-right of the picture.

It actually did work reasonably well the way it was (decent volume, but a bit of distortion). I was able to find a replacement transformer on oldradioparts.com so I ordered that.
I'm about to swap that in. I did measure ~6,000 ohm for the secondary. I wonder if I'll get that hum you described now that the two caps / resistors work-around is removed.


Messages In This Thread
Model 86 Curiosity - by Nathan Slingerland - 06-18-2018, 01:00 AM
RE: Model 86 Curiosity - by Radioroslyn - 06-18-2018, 10:04 AM
RE: Model 86 Curiosity - by Nathan Slingerland - 06-18-2018, 10:41 AM
RE: Model 86 Curiosity - by Ron Ramirez - 06-18-2018, 09:49 PM
RE: Model 86 Curiosity - by morzh - 06-18-2018, 10:13 PM
RE: Model 86 Curiosity - by Nathan Slingerland - 06-19-2018, 12:41 AM
RE: Model 86 Curiosity - by morzh - 06-19-2018, 10:27 AM
RE: Model 86 Curiosity - by Nathan Slingerland - 06-19-2018, 11:51 PM
RE: Model 86 Curiosity - by Arran - 06-20-2018, 03:37 AM
RE: Model 86 Curiosity - by Nathan Slingerland - 06-20-2018, 11:37 AM
RE: Model 86 Curiosity - by morzh - 06-20-2018, 08:50 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM
91H Code 126 Restore
When it comes to the cloth covered power cords, if they are not frayed, and are flexible, and if I can bend one without ...Arran — 06:21 PM
An attempt to remove the Field Coil from a G speaker
Could be. The central cylinder is OK, but the sides are...well. What's done is done. I wonder if some standard bobbine w...morzh — 06:02 PM
An attempt to remove the Field Coil from a G speaker
Mike; As I was saying it doesn't look like they used much of a bobbin for the field coil, not like a Magnavox one wou...Arran — 05:49 PM
Atwater-Kent 84, restoration.
This AK84 was bought, I think, last fall. For a whopping $100. It has been, according to the seller, restored. As I go ...morzh — 05:48 PM
Philco model 60
Plus I forgot that I have a spare complete Philco FC speaker, that would work perfectly, now that I don’t need it. Got i...Radios1340 — 05:36 PM

[-]
Who's Online
There are currently no members online.

>