Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Signal generator trouble
#6

Today I dug into the Heathkit. I replaced the 20 + 20 uf electrolytic with two new caps. I might restuff the old one so kept it. A quick check through other parts suggested nothing in immediate need of attention, so power was applied.

Odd sizzling sounds! Power smartly removed!

Another quick chancer - I was being treated to a superb light show from inside the variable capacitor.

I had noticed a bit of dust inside the cabinet, and sure enough, there was all sorts of grime between the plates visible on closer inspection. I set my sights on a good clean. To get this thing out was a pain - had to loosen off all the front controls to get enough movement of the chassis from the front panel. Anyway, out it came for a bath in dish detergent and gentle scrubbing with an old toothbrush. After that, a thorough drying with the hot air gun, followed by a clean and regrease of the bearings. More fettling to get it back into the chassis.

Fortunately, this did the trick, and the instrument is working nicely again, with no more fireworks. Should be a handy bit of kit.

Cheers

Ed

I don't hold with furniture that talks.


Messages In This Thread
Signal generator trouble - by EdHolland - 09-04-2018, 04:18 PM
RE: Signal generator trouble - by Eliot Ness - 09-05-2018, 08:42 AM
RE: Signal generator trouble - by morzh - 09-05-2018, 09:27 AM
RE: Signal generator trouble - by EdHolland - 09-05-2018, 01:54 PM
RE: Signal generator trouble - by EdHolland - 09-07-2018, 12:29 AM
RE: Signal generator trouble - by EdHolland - 09-16-2018, 09:28 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM
Var resistor id
Considering what it is in series with, I doubt there should be any power requirements. Of course, we should know wher...morzh — 03:23 PM
Var resistor id
Trim pot, about 1/2 watt part of focus divider. As stated 2k ohms. This appears to be a rusty chassis, resolder all ...Chas — 03:19 PM
Var resistor id
Its a Sylvania 400 oscilloscope. here is a clip of r-100. Would be nice to know the current required. Not listed in part...Martinj — 02:10 PM
The list of my radio & TV collection!
Thanks Richard. I hope you enjoy it. Here I have created an English section on the history of radio with videos in Engl...RadioSvit — 10:23 AM
The list of my radio & TV collection!
Hello RadioSvit, first all happy new year ! I will watch your new videos this week. Sincerely Richardradiorich — 09:19 AM

[-]
Who's Online
There are currently 8962 online users. [Complete List]
» 2 Member(s) | 8960 Guest(s)
AvatarAvatar

>