Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Atwater Kent model 206 weak noisy reception upper end of dial
#7

Tonight's enjoyment included taking apart that #58 tube IF can...and finding nothing amiss with it. I sleeved the grid cap wire down further to make sure that it couldn't touch at all, but oddly enough all of the wires coming out of that can were nice and pliable yet...nothing crumbling. There was even a cloth covered one!

It was like trying to pull a golf ball through a garden hose to get it out of the can though!

I was able to replace another crumbling wire that may have had a bare spot touching against one of the studs from the can, and touched up a solder joint from one of the wires leading out of the can, but outside of that, no real progress. Symptoms remain the same, even after swapping out a #58 tube and the 2A7 as you suggested. I will try the local osc test tomorrow night and the voltage checks. Never got to that tonight as the can project took a lot more time than I had planned.

Yes I knew Harlow was Amos 'n Andy's announcer too. I love listening to those shows too. Gale Gordon must've been doing double duty with Lucy and DTM at the same time in the early 60's. Have you seen the Twilight Zone episode "Static" with Dean Jagger (aka General Waverly from White Christmas)? That's one of my fav's too.

Greg V.
West Bend, WI
Member WARCI.org





Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 40-120C Filament Wiring
With these values I think you are OK; the Cmax for this tube is 40uF. Your Vbb could rise a bit, but probably not too m...morzh — 04:53 PM
Philco 40-120C Filament Wiring
BTW, someone had replaced the original 20uF/20uF filter cap with a 47uF/33uF cap. Do you think these values are safe on ...bluecap — 04:33 PM
Philco 40-120C Filament Wiring
You're correct. I was misinterpreting the key position. I now know where it is, and things are making sense. I appreciat...bluecap — 04:29 PM
Philco 40-120C Filament Wiring
I think Morzh has a good thought. Check the key position. The under chassis diagram in the Philco info shows an “H” for ...klondike98 — 04:25 PM
Philco 630csx power cord
Yes, the third wire goes to the stud on the side and is separate from the other two. I've usually used cloth covered ...Tynwald — 03:09 PM
New member
Have you tried Alabama Historical Radio Society? They possibly could recommend someone. I remember a name of Dee Hanes...morzh — 03:08 PM
Philco 46-480 Electronic Restoration
Nope, he can’t tell me the dimensions. Looks like I won’t be buying it.jrblasde — 02:38 PM
Philco 46-480 Electronic Restoration
Hello Joseph , It sounds like you found a good seller and yes shipping is really expensive ! Sincerely Richardradiorich — 02:16 PM
Philco 46-480 Electronic Restoration
There’s a lot of different search results for trust auto. I did confirm he takes Venmo, but I’ve got one last test. I as...jrblasde — 02:01 PM
Philco 91 Restore Code ??
I did the math to calculate the wattage of the resistor and found to be 47.16 watts using 3275 as fc resistance and your...dconant — 01:30 PM

[-]
Who's Online
There are currently 1885 online users. [Complete List]
» 3 Member(s) | 1882 Guest(s)
AvatarAvatarAvatar

>